Toyota Lexus IS300 Manual Download Page 31 | Manualshive

Page: 31 / 389

background image

KEYS AND DOORS

18

Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.

Consult the dealer or an experienced radio / TV
technician for help.

FCC WARNING:
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.

For vehicles sold in Canada

Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of
the device.

Replacing the battery

When you replace the battery, prepare a lithium battery
CR1616 or equivalent and a special screwdriver.

CAUTION

Special care should be taken that small children do not
swallow the removed battery or components.

NOTICE

When replacing the battery, be careful not to lose the
components, screws and O–ring.

11L028–1

1. Remove the screw, and then the cover while pushing it in
the arrow direction.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
29
30
31
32
33
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: Camcar Pages: 2

Brand: UltraGauge Pages: 55

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

STRONGARM RVR303

Brand: Blue Giant Pages: 48

Brand: Kolpin Outdoors Pages: 6

Brand: Schartec Pages: 2

Brand: Subaru Pages: 21

Brand: Kuda Pages: 3

Brand: Skoda Pages: 165

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Brand: Rugged Ridge Pages: 3

Brand: Softride Pages: 4

Easy Air Auto Screen

Brand: Wagan Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands