Toyota Lexus IS300 Manual Download Page 253 | Manualshive

Page: 253 / 389

background image

STARTING AND DRIVING

240

Good driving practice

If it is difficult to shift into reverse, put the transmission in
neutral, release the clutch pedal momentarily, and then try
again.

When towing a trailer, in order to maintain engine braking
efficiency, do not use fifth gear.

CAUTION

Be careful when downshifting on a slippery surface.
Abrupt shifting could cause the vehicle to spin or skid.

NOTICE

Make sure the vehicle is completely stopped before
shifting into reverse.

ELECTRONIC CONTROLLED

TRANSMISSION

(Vehicle with automatic transmission only)

SV31039

1

Power position 2 Normal position

The electronic controlled system has 2 modes: Normal
and Power modes.

Normal mode: For ordinary driving, Lexus recommends that
you use the normal mode to improve fuel economy.

Power mode: For more powerful acceleration and sporty
driving.

In the power mode, the ”ECT PWR” light in the instrument
cluster is on and the transmission is shifted up at higher vehicle
speeds and shifted down more responsively than in the normal
mode.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
251
252
253
254
255
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: JANE Pages: 21

Brand: Porsche Pages: 192

Brand: Dometic Pages: 158

Brand: Toyota Pages: 52

Brand: Thule Pages: 8

Brand: Park-Daddy Pages: 22

Brand: EUFAB Pages: 12

Brand: GARO Pages: 15

Interlock 700 Series

Brand: Scania Pages: 82

Crossland X 2017

Brand: Vauxhall Pages: 245

Brand: Z Flash Pages: 4

1995 Roadmaster

Brand: Buick Pages: 340

2001 Accord Sedan

Brand: Honda Pages: 372

Brand: Imiola HAK-POL Pages: 3

Brand: chinavasion Pages: 3

Rear Observation System Package RVMPKG2

Brand: Audiovox Pages: 15

Brand: Brodit Pages: 2

Brand: Whispbar Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands