manualshive.com logo in svg

Toyota Lexus IS300, Manual

Share
Download
Toyota Lexus IS300 Manual Download Page 239

STARTING AND DRIVING

226

To allow proper operation of your vehicle’s
ventilation 

system, keep the inlet grilles in front of the

windshield clear of snow, leaves, or other
obstructions.

If you smell exhaust fumes in the vehicle, drive with
the windows open and the trunk lid or back door
closed.  Have the cause immediately located and
corrected.

BEFORE STARTING THE ENGINE

1. Check the area around the vehicle before entering it.

2. Adjust seat position, seatback angle, head restraint height
and steering wheel angle.

3. Adjust the inside and outside rear view mirrors.

4. Lock all doors.

5. Fasten seat belts.

Remember to check that the service reminder indicators
function when turning the key to ”ON”, and check the fuel
gauge to see that you have sufficient fuel.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands