Toyota Lexus IS300 Manual Download Page 212 | Manualshive

Page: 212 / 389

background image

AUDIO

199

SV22039

In the ”TAPE” or ”CD” mode, the applicable functions are
shown in the lowest part of the display. Push the switch
just below to turn on each function.

(b) Tone and balance

How good an audio program sounds to you is largely
determined by the mix of the treble, mid–range, and bass
levels. In fact, different kinds of music and vocal programs
usually sound better with different mixes of treble, mid–range,
and bass.

A good balance of the left and right stereo channels and of the
front and rear sound levels is also important.

Keep in mind that if you are listening to a stereo recording or
broadcast, changing the right/left balance will increase the
volume of one group of sounds while decreasing the volume
of another.

SV22041

Each time you push the ”AUDIO CONTROL” knob, the
display changes as in the following. To adjust the tone
and balance, turn the knob.

BAS: Adjusts low–pitched tones.

MID: Adjusts mid–pitched tones.

TRE: Adjusts high–pitched tones.

FADE: Adjusts the sound balance between the front and rear
speakers.

BAL: Adjusts the sound balance between the right and left
speakers.

2003 IS300 from Aug. ’02 Prod. (OM53439U)

«
...
210
211
212
213
214
...
»

Summary of Contents for Lexus IS300






































































































































































































































































































































































































Reviews:

No comments

Related manuals for Lexus IS300

Brand: Garmin Pages: 2

Brand: iDataLink Pages: 106

Brand: Lancia Pages: 386

Brand: Daewoo Pages: 68

Brand: Hyundai Pages: 437

Brand: Haibang Pages: 6

Brand: Compass Pages: 16

Brand: Chevrolet Pages: 376

Brand: Mazda Pages: 15

Brand: TBC Pages: 12

Brand: Prorack Pages: 14

HU-4421-XL-SDK01

Brand: FALCON RIDGE Pages: 5

1995 Cutlass Supreme

Brand: Oldsmobile Pages: 340

Brand: Prorack Pages: 15

Brand: Edelbrock Pages: 4

HOLLANDIA 700 - 20 Series

Brand: Webasto Pages: 30

Brand: Ranger design Pages: 22

Brand: Lexus Pages: 878

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands