Toyota Land Cruiser 2007 Manual Download Page 31

Page: 31 / 308

For replacement, use a CR2016 lithium
battery or equivalent and a special screw-
driver.

CAUTION

Special care should be taken to pre-
vent small children from swallowing
the removed battery or components.

NOTICE

When replacing the battery, be care-
ful not to lose the components.

Replace only with the same or
equivalent type recommended by a
Toyota dealer.

Dispose of used battery according
to the local laws.

Replace the battery by following these
procedures:

1. Remove the screw, and then the cover.

11C522a

2. Remove the module from the key

frame.

—Replacing battery

Summary of Contents for Land Cruiser 2007





















































































































































































































































































































Search results

Summary of Contents for Land Cruiser 2007

Reviews:

Related manuals for Land Cruiser 2007

Brands by name

Popular brands

Toyota Land Cruiser 2007, Manual

Search results

Summary of Contents for Land Cruiser 2007

Reviews:

Related manuals for Land Cruiser 2007

Brands by name

Popular brands