Toyota Corolla 2008 Owner'S Manual Download Page 32 | Manualshive

Page: 32 / 310

background image

’08 Corolla_U (L/O 0706)

206

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

1. Check the area around the vehicle be-

fore entering it.

2. Adjust seat position, seatback angle,

seat cushion height, head restraint
height and steering wheel angle.

3. Adjust the inside and outside rear view

mirrors.

4. Lock all doors.

5. Fasten seat belts.

1. Apply the parking brake firmly.

2. Turn off unnecessary lights and acces-

sories.

3. Manual transmission: Press the clutch

pedal to the floor and shift the trans-
mission into neutral. Hold the clutch
pedal to the floor until the engine is
started. A starter safety device will pre-
vent the starter from operating if the
clutch pedal is not fully depressed.

Automatic transmission: Put the se-
lector lever in “P”. If you need to re-
start the engine while the vehicle is
moving, put the selector lever in “N”.
A starter safety device will prevent the
starter from operating if the selector
lever is in any drive position.

4. Automatic transmission only: De-

press the brake pedal and hold it to
the floor until driving off.

Before starting the engine, be sure to fol-
low the instructions in “(a) Before crank-
ing”.

Normal starting procedure

The multiport fuel injection system/sequen-
tial multiport fuel injection system in your
engine automatically controls the proper
air−fuel mixture for starting. You can start
a cold or hot engine as follows:

With your foot off the accelerator pedal,
crank the engine by turning the key to
“START”. Release it when the engine
starts.

Engine should be warmed up by driving,
not in idle. For warming up, drive with
smoothly turning engine until engine cool-
ant temperature is within normal range.

If the engine stalls...

Simply restart it, using the correct proce-
dure given in normal starting.

If the engine will not start...

See “If your vehicle will not start” on page
220 in Section 4.

Before starting the engine

How to start the engine—
(a) Before cranking

(b) Starting the engine

«
...
30
31
32
33
34
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Brand: Raytel LLC Pages: 40

Brand: AA Products Pages: 4

Brand: Cadillac Pages: 20

Brand: Draw tite Pages: 4

Brand: Mercedes-Benz Pages: 329

Brand: SuperATV Pages: 7

Brand: Chevrolet Pages: 428

Brand: Volvo Pages: 211

Brand: Yakima Pages: 12

Brand: Axxess Pages: 16

Brand: Black Horse Off Road Pages: 7

Brand: Linear Logic Pages: 8

Brand: Kia Pages: 58

Portable Car Umbrella

Brand: Mynew Pages: 5

Brand: Grillo Pages: 71

Brand: Fabbri Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands