admin
Click
Settings
Wi-Fi
.
Select TOTOLINK N600R, no password
required by default.
When connected, the Web page of TOTOLINK
N600R will pop up automatically.
10
9
Try any website to test the Internet. Here we type in www.totolink.net.
Now the router’s Status interface turns up, it shows connected type
and IP address & DNS you get.
Hardware Installation
1. Please disconnect the power adapter and all cables during
thunderstorm weather;
2. Keep away from heat source and keep well ventilated;
3. Please pay attention to the waterproofing and moisture-proof
when storing, transporting and running.
4. The power adapter must be original or approved by TOTOLINK.
5. Put the router in flat places.
Set Up PC
Windows 10
Windows Vista/7
For Windows 10 Operating System, please comply with following steps to set up.
If you use ADSL Modem to access the Internet, please follow below steps. For houses that there is only one
Ethernet cable from the wall, please plug the Ethernet cable to the router’s WAN port directly.
Click
Start
( )---
All apps
---
Windows System
---
Control Panel
---
Network and Sharing Center
---
Change adapter setting
, right-click
Local Area
Connection
, and choose
Properties
.
Double-click
Internet Protocol
Version 4 (TCP/IPv4)
.
Choose
Obtain an IP address automatically
and
Obtain DNS server address automatically
,
click
OK
; And then click
OK
.
For Windows Vista or Windows 7 Operating System, please comply with following steps to set up.
Click
Start— Control Panel— Network
and Internet— Network Connection
,
right-click
Local Area Connection
,
and choose
Properties
.
Double-click
Internet Protocol
Version 4 (TCP/IPv4)
.
Choose
Obtain an IP address automatically
and
Obtain DNS server address automatically
,
click
OK
; And then click
OK
.
Quick Installation Guide
600Mbps Wireless N Router
NOTE:
Set Up Router
Please set up the router following below steps.
Run any Web browser.
For more information, please go to www.totolink.net
The
USER LOGIN
page will pop up automatically. Enter
admin
for both
User Name and Password, click
LOGIN
. (The auto pop-up page only for
first connection, future Login please enter “
192.168.0.1
” in address bar)
Now you can see the
Easy Setup
interface.
Choose the
WAN Connection Type
and enter the parameters
provided by your
Internet Service Provider
.
Wireless Settings, you can change or retain your SSID (wireless network name).
Choose the encryption type. The
WPA2-PSK
is recommended, then type
in your password ( password length more than 8 characters).Then click
Apply
to save the Settings.
7
Here we take PPPoE as example. You are required to enter the User
Name and Password.
Information in this document is subject to change without prior notice.
8
Wait for a while, Internet connected successfully! Please click
finish
.
LED Indicators
WAN
LAN
Blink
Off
On
The router is working under normal power.
Status
Red
Green The Turbo switch is enabled and the router is working
under middle power.
The router is working normally or resetting.
Power is off.
The WAN port is connected, the Internet is available.
Off
The WAN port is not connected, the Internet is unavailable.
On
There is device connected to LAN port 1/2/3/4.
Off No device connected to LAN port 1/2/3/4.
Ports and Buttons Description
WAN
LAN
Turbo
RST/WPS
Connect with the power adapter
DC IN
Connect to ADSL modem or Internet Cable
Connect to PC or Laptop
Press for 1s, WPS enabled; press for more than 5s, Reset
function enabled.
Improve the router’s working power, extend Wi-Fi coverage.
Suitable for: N600R
Copyrights TOTOLINK All rights reserved. Website: http://www.totolink.net
V1.1602
Network
Cable
Network
Telephone
Cable
Cable
ADSL Modem
Router
WPS: press for about 1~3 seconds, the system LED indicator keep solid
light, it means WPS working;
RST: press for about 5~8 seconds, all LEDs blinks quickly, the device will
restore to factory default settings.
NOTE:
After you set the Key, please remember your SSID and the Key to connect with
your wireless LAN.
Auto Pop-up Setting page for First Wi-Fi Devices Connection
FAQ
What can I do if I forget the router’s Web Login page User
Name and Password?
4
How to reset the router to default settings?
1. Please make sure your router’s power is on regularly, then press the
RST/WPS button for about 5~8s.
2. Loosen the button until your router’s LED lights all flashing, then you
have reset your router to default settings.
Please reset your router to default settings firstly, the default IP address is
192.168.0.1
, both default User Name and Password are
admin
.
How Turbo switch improve the router’s wireless
performance?
By default, the Turbo switch is off. After you slide the Turbo switch to on,
the router’s output power will be increased by about 6dBm theoretically,
which means your Wi-Fi signal will be improved and the Wi-Fi coverage
will be extended (depending on the environment). But the radiation will
be enhanced as well. So if there is any pregnant women or infants at
home, we recommend you not enable Turbo switch.
→
3
N600R
N600R
N600R
Wall Socket
Wall Socket
Note: This function is only suitable for iPhone and a few Android smart phones. If the auto pop-up page not turns up on your phone, please use PC to set up your router.
