Toshiba TXZ SERIES Reference Manual Download Page 58 | Manualshive

Page: 58 / 67

background image

TXZ Family

Serial Peripheral Interface

2019-02-28

58 / 67

Rev. 3.0

4.2.9. [TSPIxSR] (TSPI

Status Register

)

Bit

Bit Symbol

After

reset

Type

Function

31

TSPISUE

0

R

TSPI modify status flag

0: Modification is enabled.
1: Modification is disabled.

If <TSPISUE> is "0", the TSPI is not transmitting or receiving, thus
the register setting can be modified.
<TSPISUE> is "0" in the following conditions.(Please refer to Table
4.2):

1. Reset is input.
2. Software reset occurs.

3. In the continuously transfer mode, the time when current

transferring frame is finished when

[TSPIxCR1]

<TRXE>=0 is

set.

4. In the burst mode, the timing when specified number of

transfers is finished.

5. The time when current transferring frame is finished when

[TSPIxCR1]

<TRXE>=0 is set during burst transfer.

However, even if above conditions are satisfied, <TSPISUE> does
not become "0" when the transmit FIFO or receive shift register is
full. To set <TSPISUE>=0, read the receive FIFO and transfer a
receive value in the receive shift register to the receive FIFO.

30:24

-

0

R

Read as "0".

23

TXRUN

0

R

Transmit shift operation flag

0

:

Stop

1

:

Operation

A status flag indicates the transmit shift operation is ongoing.
Combination of <TXRUN> and <TFEMP> bits indicates the
following status:

<TXRUN> <TFEMP>

Conditions

0

0

Stop or wait for the next transmission

1

Completed transmission and the
transmit FIFO is empty.

1

-

In transmission

<TXRUN> is set when data exists in the transmit shift register even
if data does not exist in the transmit FIFO.

22

TXEND

0

R

Transmit completion flag

0: -
1: Transmit is complete.

A flag that is set at the time when transmission is complete.
This flag is set at the last frame (TSPIxCS0/1/2/3 is deasserted) in
the single transfer, burst transfer or continuously transfer after one
frame transfer.

W

This bit is cleared by writing "1".

0: Don’t care
1: Flag is cleared.

When the setting by transmission completion and clearing by
writing "1" occur simultaneously, the setting by transmission
receives a higher priority.

21

INTTXWF

0

R

Transmit FIFO interrupt flag

0

:

No interrupt

1

:

Interrupt occurs

This bit is set when remaining data in the transmit FIFO reaches a
TIL value from a fill level setting value (TIL)+1.

«
...
56
57
58
59
60
...
»

Summary of Contents for TXZ SERIES




































































Reviews:

No comments

Related manuals for TXZ SERIES

Brand: NAVITAS Pages: 7

Brand: BADODOSECURITY Pages: 8

Brand: Bard Pages: 8

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Brand: RadioMaster Pages: 10

Brand: IFM Pages: 49

Brand: EasyIO Pages: 17

TruPortal TP-ADD-1DIP

Brand: Interlogix Pages: 9

Brand: Linear Technology Pages: 32

Brand: FuzzDog Pages: 9

DMC-40x0 Series

Brand: Galil Motion Control Pages: 280

WFHC 06Z 02 HC RF 24

Brand: Watts Pages: 18

Errata MSP430F6779

Brand: Texas Instruments Pages: 27

Brand: Brooks Pages: 66

Brand: Beckhoff Pages: 67

Brand: Omron Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands