Toshiba TS3100 Instruction Manual Download Page 125

Page: 125 / 154

TRANSPORTATION AND INSTALLATION MANUAL

125

Tool Wiring (Robot Arm Side)

11.1.2.

Four input signals are provided for sensors, etc. and four control signals for solenoid

valves, etc. A supply power signal of 24 VDC is also provided. They are connected to

the controller. The wiring arrangement for these cables is shown in Fig. 11.1. The

wires are connected to the connectors on the arm 2 (1). The customer should provide

the following connectors to connect the cables.

Cannon connector (standard)

Type: Angle plug JN2FS10SL2-R

(Maker: Japan Aviation Electronics Industry)

Type of contact: JN1-22-26S-PKG100

Adaptive cable: AWG26~AWG28

JN1-22-22S-PKG100

AWG21~AWG25

JN1-22-20S-PKG100

AWG20

If the above-mentioned parts cannot be procured, we will prepare the cables. Table

5.1 shows the HAND cable (option) list.

DANGER

• Be sure to use the designated wire. Otherwise, fires or faults may be

caused.

• When connecting the connector and wires, make sure not to mistake the

terminal arrangement.

• After making the connection, use a tester, etc., to confirm the connection.

If the separately installed sequencer or the like is used for control, remove the connector

panel of the base portion and separate the connectors HIN and HOUT on the

rear. Then connect the cable of the sequencer or the like through the cable inlet of the

connector panel. (See Fig. 11.1.) For ahead of the HIN and HOUT connectors,

the user should prepare the following plug connectors and connect the cables. The

current is 1 A or less per cable.

Type of connector:

HIN

SMR-06V-B (Maker: J.S.T. Mfg.)

HOUT

SMR-10V-B (Maker: J.S.T. Mfg.)

Type of contact:

SYM-001T-P0.6

Adaptive cable: AWG22~AWG28

ROBOT connector type

Type of connector:

HIN

SMP-06V-BC (Maker: J.S.T. Mfg.)

HOUT

SMP-10V-BC (Maker: J.S.T. Mfg.)

Summary of Contents for TS3100



























































































































































Search results

Summary of Contents for TS3100

Reviews:

Related manuals for TS3100

Brands by name

Popular brands

Toshiba TS3100, Instruction Manual

Search results

Summary of Contents for TS3100

Reviews:

Related manuals for TS3100

Brands by name

Popular brands