Toshiba TRST-A00 SERIES Page 23 Owner'S Manual Download | Manualshive

Page: 23 / 35

background image

5. INSTALLATION PROCEDURE

EO1-13027

5.2 Connecting the Drawer

5-4

5.2 Connecting the Drawer

1)

Turn the printer power OFF.

2)

Connect the drawer cable to the drawer interface connector in the correct orientation.

[Drawer interface connector] (6-pin modular connector)

A Drawer cable which connects the printer to a drawer is connected to this connector.
To this connector, a TOSHIBA drawer can be connected. Do not connect anything other than the
connectable drawer.

NOTE: For connectable drawers, refer to your nearest authroized TOSHIBA TEC representative.

[Ground terminal] (6-pin modular connector)

The drawer interface cable’s ground wire is secured to this terminal.

«
...
21
22
23
24
25
...
»

Summary of Contents for TRST-A00 SERIES




































Reviews:

No comments

Related manuals for TRST-A00 SERIES

Brand: Zeka Pages: 54

Brand: Xerox Pages: 9

Brand: Xerox Pages: 2

Brand: Xerox Pages: 8

Brand: Xerox Pages: 4

Brand: Xerox Pages: 150

Brand: Xerox Pages: 4

Brand: Xerox Pages: 6

Brand: Xerox Pages: 2

DocuPrint N2125

Brand: Xerox Pages: 246

DocuPrint N2025

Brand: Xerox Pages: 378

DocuPrint N2025

Brand: Xerox Pages: 176

DocuPrint C3290 FS

Brand: Xerox Pages: 240

Brand: Xerox Pages: 5

Brand: Xerox Pages: 7

Brand: Xerox Pages: 2

Brand: Xerox Pages: 10

Brand: Xerox Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands