Toshiba Strata CT DKT2520-FS User Manual Download | Manualshive

Page: 25 / 104

background image

The Basics

Message Waiting

Strata CTX DKT3000/2000-Series Telephone 05/02

11

Message Waiting

Use your

0VJ

LED/button and LCD to see/retrieve message(s).

An extension can receive up to four simultaneous Message Waiting indications and
LCD messages. One message is reserved for the Message Center.

Your telephone can be programmed to have up to four additional (flexible) Message
Waiting buttons/LEDs. Check with your CTX System Administrator to see if these
buttons have been programmed on your telephone. If so, substitute them when the

0VJ

button/LED is mentioned in the following steps.

Responding to a Lit Msg LED

1. On an LCD telephone, if you see a “+,” press

6FUROO

to display additional

messages; otherwise, go to Step 2. The “+” indicates additional messages. The
LCD can show up to three station messages for your extension and three for each
additional (phantom) extension that you may have.

2. Press

0VJ

, then lift the handset. Your telephone rings the extension or voice mail

device that sent the indication. The LED continues to flash red.

3. After answering the message(s), place the handset back on-hook.

4. If the Msg LED continues to flash, you have more messages; repeat Steps 1~3

above to retrieve them. Voice mail devices turn off the LED/LCD indications after
a short delay, after you checked all messages.

5. To manually turn off your Msg LED, press your extension button, then press

. Do this step for each message received.

«
...
23
24
25
26
27
...
»

Summary of Contents for Strata CT DKT2520-FS









































































































Reviews:

No comments

Related manuals for Strata CT DKT2520-FS

Brand: Panasonic Pages: 140

Brand: Panasonic Pages: 32

Brand: Samsung Pages: 38

Brand: 2N Pages: 32

Brand: Yezz Pages: 5

Brand: X-View Pages: 42

Brand: TECNO MOBILE LIMITED Pages: 6

Brand: ShoreTel Pages: 2

Brand: EMPORIA Pages: 2

Brand: M4 Pages: 19

Brand: UVI Group Pages: 8

Brand: ORA Pages: 30

Brand: OUKITEL Pages: 39

Brand: OUKITEL Pages: 60

Brand: Xiaomi Pages: 52

Transform SPH-M920

Brand: Samsung Pages: 238

Brand: Samsung Pages: 203

VERIZON SCHU460

Brand: Samsung Pages: 193

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands