manualshive.com logo in svg

Toshiba Strata CIX40, User Manual

The Toshiba Strata CIX40 is a powerful communication system that enhances business connectivity. To get started quickly, download the free Quick Start Manual from our website. This manual provides step-by-step instructions, allowing you to maximize the productivity and efficiency of your Toshiba Strata CIX40 system.

Share
Download
background image

Administrator Programming

IP5131-SDL Settings

134

Strata CIX IP5000-series Telephone UG     07/09

IP5131-SDL Settings

This section contains instructions to configure the IP5131-SDL telephone. All 
instructions found in this section pertain to the items found in the IP Configurations 
screen of the IP5131-SDL telephone.

Configurations

Press 

Hold

+

3

+

6

+

9

 (simultaneously) to display the IP 

Configurations main screen.

To access any of the screens that relate to an item on 
the Configurations screen

 Press the soft key that corresponds to the item. The 
details pertaining to that item display.

Note

The following table explains each of the items 
displayed on the Configurations screen.

I

TEM

I

NFORMATION

 D

ISPLAY

Term Info

Displays the Software Version, the MAC address, the Regional Code 
and xIPU address. You can press the EXIT soft key to go back to the IP 
Configurations screen.

Note

This screen is for display only and you cannot make any 
changes to the settings.

Network

Page 1:Displays or sets the DHCP, IP Address, Subnet, the default 
gateway, station information and LIPU Address.

Page 2:Displays or sets node, IPU Mode, Primary IPU, Secondary IPU 
and Port Settings.

Page 3:Displays or sets Auto Login Mode and Auto Login password.

Advance

Page 1:Displays or sets the Primary Name Server, the Secondary Name 
Server, GRQ Port, RRQ Port, and AP Address

Page 2:Displays or sets the Admin address upper and lower bound, the 
User ID and password, as well as the Dynamic Port Base.

Page 3:Displays or sets the VLAN Setting, PC Port type and PC Port 
VLAN ID.

IP Configurations

Term Info

Network

Advance

Sound

Others

Key Repeat

Net Diag

Factory

Initialize

Reset

Config

Summary of Contents for Strata CIX40

















































































































































































































Reviews:

No comments

Related manuals for Strata CIX40

GAMDIAS Aura GC2 Quick Installation Manual preview
Aura GC2
Brand: GAMDIAS Pages: 15
Intel SRCSASBB8I - RAID Controller Hardware User'S Manual preview
SRCSASBB8I - RAID Controller
Brand: Intel Pages: 36
SIIG ID-P20211-S1 Quick Installation Manual preview
ID-P20211-S1
Brand: SIIG Pages: 20
Mitsubishi 32172 User Manual preview
32172
Brand: Mitsubishi Pages: 874
Mellanox Technologies ConnectX 3 Pro User Manual preview
ConnectX 3 Pro
Brand: Mellanox Technologies Pages: 57
Airlink101 AWMB100 User Manual preview
AWMB100
Brand: Airlink101 Pages: 46
Z-Com ZCN-1523H-5-16 Quick Installation Manual preview
ZCN-1523H-5-16
Brand: Z-Com Pages: 18
Powerleap PL-PROMMX Manual preview
PL-PROMMX
Brand: Powerleap Pages: 28
ADS Technologies PTV-370 Driver Manual preview
PTV-370
Brand: ADS Technologies Pages: 1
CSL 300295 User Manual preview
300295
Brand: CSL Pages: 24
RAID N8103-134 Setup Manual preview
N8103-134
Brand: RAID Pages: 80
Homeworks HQP7-RF-2 Installation Instructions Manual preview
HQP7-RF-2
Brand: Homeworks Pages: 24
LevelOne FSW-0512 Specification Sheet preview
FSW-0512
Brand: LevelOne Pages: 2
Alcatel-Lucent Service Aggregation Router 7705 Installation Manual preview
Service Aggregation Router 7705
Brand: Alcatel-Lucent Pages: 20
DAPAudio D2081 Manual preview
D2081
Brand: DAPAudio Pages: 33
R3 Bridge E User Manual preview
Bridge E
Brand: R3 Pages: 48
Adeunis RF ARF8264AAA Quick Start Manual preview
ARF8264AAA
Brand: Adeunis RF Pages: 9
protech ProX-1550 User Manual preview
ProX-1550
Brand: protech Pages: 110

Brands by name

Popular brands

Load more brands