Toshiba Strata CIX IP5000 Series User Manual Download Page 77 | Manualshive

Page: 77 / 216

background image

Feature Operations

Call Waiting

Strata CIX IP5000-series Telephone UG 04/09

59



To transfer a call directly to Voice Mail (VM)

1. While on a call, press

Cnf/Trn

.

2. Enter

#407

.

3. Enter the VM mailbox number (usually the same as the extension number) +

#

.

4. Hang up and the caller is connected to the VM mailbox. This feature does a blind

transfer to VM.



To transfer a call directly to VM with a DSS button

1. While on a call, press

Cnf/Trn

.

2. Press the DSS button programmed to the voice mail number.
3. Hang up and the caller is connected to the VM mailbox.

Call Waiting

You can answer a call that is transferred to your station, even when your station is
busy. When another call is camped onto your station, you hear two Camp-on tone
beeps and the extension or Line LED flashes red (on-hold).

If a call is sent to your station when busy, and your station does not have an extension
button available to receive the call, two camp-on tone beeps are sent to your
telephone. You must disconnect or transfer the existing call to answer the waiting call.



To answer a waiting call by placing the current call on hold



Press

Hold

.

The existing call is placed on hold. The camped-on line rings your

station (the Line LED flashes green - incoming call)....or if your telephone has the
Auto Hold feature, just press the flashing extension button.

You are connected to the transferred call. The extension or Line LED flashes green
(in-use).

Note

See your System Administrator to find out if you have Auto Hold.



To answer a waiting call by disconnecting or transferring the current call



Hang up or transfer the existing call; the camped-on call rings your station. The
camped-on line rings your telephone and the Line LED flashes green (incoming call).

...or press the flashing extension or

Line

. The existing call is placed on hold. The

camped-on line rings your station (the Line LED flashes green - incoming call).
This disconnects the current call and connects you to the transferred call. The
extension or Line LED flashes green (in-use).

«
...
75
76
77
78
79
...
»

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Reviews:

No comments

Related manuals for Strata CIX IP5000 Series

Brand: Yealink Pages: 4

Brand: Yealink Pages: 148

Brand: Yealink Pages: 2

Brand: Yealink Pages: 131

Brand: Yealink Pages: 159

Brand: Yealink Pages: 9

Brand: Unitech Pages: 2

Brand: BENQ-SIEMENS Pages: 132

Brand: Hanlong Pages: 68

DigiWalker A701

Brand: Mio Pages: 168

Brand: Kyocera Pages: 2

Brand: HTC Pages: 58

Brand: Netway Pages: 68

Brand: Lephone Pages: 23

COMMUNICATOR C100S

Brand: Polycom Pages: 2

Brand: Majestic Pages: 41

Brand: Samsung Pages: 145

Brand: Samsung Pages: 125

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands