Toshiba Strata CIX IP5000 Series User Manual Download Page 51 | Manualshive

Page: 51 / 216

background image

SoftIPT

Message Waiting

Strata CIX IP5000-series Telephone UG 04/09

33

Fixed Buttons

The fixed buttons on your telephone enable you to perform standard functions quickly
and easily. These buttons are described in

Chapter 2 – The Basics

.

Flexible Buttons

All Flexible Buttons must be programmed for your telephone in system programming
and vary for individual telephones. If a button does not appear on your display or
telephone keystrip label, see your System Administrator for button assignments.

Line Buttons

You may have buttons designated as

Line

and/or

Pooled Line Grp

which enable

you to directly access outside lines.

Pooled Line Grp

enables you to access

available CO Lines from a group of lines appearing under one button.

Liquid Crystal Display

The Liquid Crystal Display (LCD) on the SoftIPT will display information similar to
the large 9-line IP telephone display:

•

Desk Clock and Calendar in idle mode

•

Call Duration during an outside call

•

Operational, Advisory, and Notification messages

LCD Control Buttons

There are two types of LCD button functions: LCD Control Buttons and Soft Keys.

When the Soft Key prompts appear on the LCD, the LCD Control Button just below
the prompt offers access to that feature. See

“Soft Keys” on page 11

for more

information.

•

SK1

is generally used as a Soft Key.

•

Pressing

SK2

switches you from the Call Forward (CF) display to the User Name

display.

•

Pressing

SK3

advances you through information.

«
...
49
50
51
52
53
...
»

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Reviews:

No comments

Related manuals for Strata CIX IP5000 Series

Brand: Pantech Pages: 101

Brand: Pantech Pages: 47

Yealink SIP-T48G

Brand: Yealink Pages: 2

Yealink SIP-T48G

Brand: Yealink Pages: 4

Yealink SIP-T46G

Brand: Yealink Pages: 38

Brand: Yealink Pages: 255

Yealink SIP-T48G

Brand: Yealink Pages: 105

Brand: Yealink Pages: 13

Brand: Yealink Pages: 77

Brand: Alcatel Pages: 73

Brand: Tyco Pages: 36

Brand: i-mobile Pages: 58

Brand: Light Repute International Pages: 15

Brand: TIPTEL Pages: 56

Brand: Docomo Pages: 194

Brand: Mitel Pages: 60

Brand: NEC Docomo Pages: 27

Brand: Kogan Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands