Toshiba Strata CIX IP5000 Series User Manual Download Page 43 | Manualshive

Page: 43 / 216

background image

Strata CIX IP5000-series Telephone UG 04/09

25

On a Call

While on a call you can perform the following:

Switching Between Handset and Speakerphone



Press

Spkr

and place the handset on-hook to switch from handset to speakerphone

mode.



Take the handset off-hook to switch from speakerphone to handset mode.

Microphone (Mic/Mute) Button

This button toggles between Mic and Mute. When Mic button is lit, handsfree
communication is supported, when Mic is pressed again and light is off, Mute is
enabled and mutes both the microphone and the handset.

Hold



To place a call on hold, press

Hold

. Your LCD shows the line on hold. The held

Line’s LED flashes green while appearances of the line at other stations flash red.

•

To return to the held call, press the flashing held

Line

button.

•

If you do not return to the held call within a specified time, it rings back to your
telephone. The call remains camped-on to your station.

•

If the held party hangs up, the call is released.

•

See the Call Pickup section to pick up a call on hold from another extension.

Exclusive Hold

This feature enables you to place a call on hold so that only you can retrieve it.



While on a call, press

Hold

twice. That line’s LED flashes green while

appearances of the line at other stations are steady red (in use).

«
...
41
42
43
44
45
...
»

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Reviews:

No comments

Related manuals for Strata CIX IP5000 Series

blackview Crown

Brand: Iget Pages: 76

Brand: Audiovox Pages: 137

Brand: Allview Pages: 108

Brand: Archos Pages: 75

DIAL-ALERT AD-105 Guide

Brand: SkyLink Pages: 14

Brand: Sprint PCS Pages: 145

Brand: Nortel Pages: 52

Brand: Flyingvoice Pages: 51

Brand: STK Professional Audio Pages: 13

Brand: GAI-Tronics Pages: 92

Brand: Samsung Pages: 159

Brand: Samsung Pages: 171

Brand: Samsung Pages: 158

Brand: iNels Pages: 16

Brand: Zte Pages: 114

Brand: Philips Pages: 2

Brand: Philips Pages: 32

Brand: Philips Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands