Toshiba Satellite A350 Series Maintenance Manual Download | Manualshive

Page: 190 / 297

background image

Error! Style not defined. Error! Style not defined.

4 Replacement Procedures

Satellite A350D Maintenance Manual

4-13

Installing the HDD

Install the HDD according to the following procedures.

CAUTION: To avoid damage, always hold the HDD only by its sides.

1.

Place the main HDD into the main HDD plate.

2.

Secure the HDD and its plate with four M3x3 screws.

CAUTION: To prevent the HDD plate from being distorted when installing the HDD pack
into the laptop, do not press the center of the HDD pack. Always hold the HDD pack by its
sides.

3.

Install the HDD pack into the correct position in the laptop. Connect the HDD pack to the
laptop.

4.

Secure the main HDD door by tightening two M2.5x6 screws.

5.

Place the 2

nd

HDD into the 2nd HDD plate.

6.

Place the two HDD brackets in the correct sides of the plate and secure them with four
M3x3 screws.

7.

Install the HDD pack into the correct position in the laptop. Connect the HDD pack to the
laptop.

8.

Secure the 2

nd

HDD door by tightening two M2.5x4 screws.

Downloaded from LpManual.com Manuals

«
...
188
189
190
191
192
...
»

Summary of Contents for Satellite A350 Series










































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A350 Series

Aspire 1670 Series

Brand: Acer Pages: 118

Brand: Acer Pages: 94

AcerNote Nuovo 970

Brand: Acer Pages: 4

Brand: Acer Pages: 16

9410-2829 - Aspire

Brand: Acer Pages: 108

Brand: Acer Pages: 130

Brand: Acer Pages: 93

Aspire 1360 Series

Brand: Acer Pages: 104

Brand: IBM Pages: 331

ThinkPad i Series

Brand: IBM Pages: 5

Thinkpad X30 Series

Brand: IBM Pages: 22

Brand: IBM Pages: 2

Brand: Targus Pages: 4

Brand: Targus Pages: 2

Brand: MSI Pages: 80

Brand: Ace Pages: 282

Brand: Hena Pages: 7

5530 Mono Laser

Brand: Dell Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands