Toshiba Satellite A350 Series Maintenance Manual Download Page 149 | Manualshive

Page: 149 / 297

background image

3. Tests and Diagnostics

18

the “OK” column will end this test.

It will indicate whether the subtests pass or fail after three questions.

NOTE: The above figure has three compartments although the Touch Pad installed may
only have two buttons. In this case, the central compartment in the figure does not
correspond to any button.

3.11 LCD Pixels Mode Test

This LCD pixels mode test checks whether video display is fine.

This test includes two modes of the test:

1.

Text Mode

- including 40*25 (16 colors) and 80*25 (2/16colors).

2.

VGA Mode

- including 320*200 (4/16/256 colors), 640*200 (2/16 colors), 640*350 (2/16 colors),
640*480 (2/16/256 colors), 800*600 (256 colors) and 1024*768 (256 colors).

The screen should display as below, indicating whether the test is passed or failed after the
question.

Downloaded from LpManual.com Manuals

«
...
147
148
149
150
151
...
»

Summary of Contents for Satellite A350 Series










































































































































































































































































































Reviews:

No comments

Related manuals for Satellite A350 Series

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 55

Brand: Panasonic Pages: 21

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 16

NOTEBOOK Q7M ENTERTAINMENT XD

Brand: YAKUMO Pages: 41

Brand: Xebec Pages: 15

VERSA DAYLITE 3-CELL REMOVABLE BATTERY

Brand: NEC Pages: 6

Brand: NEC Pages: 6

Latitude 0NW164A01

Brand: Dell Pages: 2

Satellite 4060CDT

Brand: Toshiba Pages: 3

Satellite 4025CDT

Brand: Toshiba Pages: 3

Satellite 4010CDS

Brand: Toshiba Pages: 3

Satellite 4015CDS

Brand: Toshiba Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands