Toshiba RAS-18PAVSG-E Service Manual Download Page 108

Page: 108 / 137

No.

Part name

rocedure

Remarks

Electric part

box assembly

1) Follow the procedure item 3 .

2) Remove screw holding the electric part cover.

3) Disconnect the connectors for the fan motor

and louver motor from P.C. board assembly.

4) Disconnect the cord motor of Louver VT (5P)

from the Louver VT (L/R) connector.

5) Remove the earth screw and earth line from

evaporator.

6) Pull out TC sensor from sensor holder of the

evaporator.

7) Remove the 2 fixing screws that secures the

electric parts box assembly, unit display

assembly and remove the electric parts box

assembly.

Earth screw

Earth line

Washer

TC sensor

Sensor holder

Electric part cover

Screw

Connectors

Fan motor connector

Louver motor connector

Earth line

TC sensor

TA sensor

Louver motor VT (L) connector

Louver motor VT (R) connector

(black)

Screw

Unit display

Electric parts box

FILE NO. SVM-17001

- 107 -

Summary of Contents for RAS-18PAVSG-E










































































































































Search results

Summary of Contents for RAS-18PAVSG-E

Reviews:

Toshiba RAS-18PAVSG-E, Service Manual, Page: 108 / 137

Search results

Summary of Contents for RAS-18PAVSG-E

Reviews: