manualshive.com logo in svg

Toshiba RAS-10G2AVP Series, Installation Manual, Page: 2 / 16

Share
Download
Toshiba RAS-10G2AVP Series Installation Manual Download Page 2

PRECAUTIONS FOR SAFETY

 ...........................................................................................................................................1

INSTALLATION DIAGRAM OF INDOOR AND OUTDOOR UNITS

 ...................................................................................3

„

  Optional Installation Parts ...............................................................................................................................................3

INDOOR UNIT

 .....................................................................................................................................................................4

„

 Installation Place .............................................................................................................................................................4

„

  Cutting a Hole and Mounting Installation Plate ...............................................................................................................4

„

  Piping and Drain Hose Installation ..................................................................................................................................5

„

  Indoor Unit Fixing ............................................................................................................................................................6

„

  In case of Indoor unit is 

fi

 xed to Installation plate with screws ........................................................................................6

„

 Drainage .........................................................................................................................................................................6

OUTDOOR UNIT

 .................................................................................................................................................................6

„

 Installation Place .............................................................................................................................................................6

„

  Refrigerant Piping Connection ........................................................................................................................................6

„

 Evacuating  .....................................................................................................................................................................7

ELECTRICAL WORKS

 .......................................................................................................................................................8

„

 Wiring Connection ...........................................................................................................................................................8

„

  Power Supply and Connecting Cable Connection ..........................................................................................................9

„

  Power supply input Wiring Diagram ..............................................................................................................................10

„

  Wiring between DRED (Demand response enabling device) and Outdoor Unit ........................................................... 11

„

 Connection procedure ................................................................................................................................................... 11

„

  Outdoor unit preparation ...............................................................................................................................................12

OTHERS

 ............................................................................................................................................................................13

„

 Gas Leak Test ...............................................................................................................................................................13

„

  Remote Control A-B Selection ......................................................................................................................................13

„

  Test Operation  ..............................................................................................................................................................13

„

  Auto Restart Setting  .....................................................................................................................................................13

CONTENTS

EN

1115751104-EN.indd   2

1115751104-EN.indd   2

5/26/2557 BE   10:45 AM

5/26/2557 BE   10:45 AM

Summary of Contents for RAS-10G2AVP Series

















Reviews:

No comments