manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Service Manual, Page: 63 / 333

Share
Download
Toshiba MMY-MAP0804FT7(Z) Service Manual Download Page 63

– 63 –

Sensor

(TC2)

M

Fan

Fan motor

Sensor

(TCJ)

Sensor

(TC1)

Strainer

Liquid
side

Gas side

Capillary tube

Sensor

(TA)

Pulse Motor 

Valve  

(PMV)

Heat exchanger 

at indoor side

Functional part name

Functional outline

Pulse Motor Valve

1. Single cooling

(Connector CN082 (6P): Blue)
1) Controls super heat in cooling operation
2) Controls under cool in heating operation
3) Recovers refrigerant oil in cooling operation
4) Recovers refrigerant oil in heating operation

PMV

Temp. Sensor

(Connector CN104 (2P): Yellow)
1) Detects indoor suction temperature

1.TA

(Connector CN100 (3P): Brown)
1) Controls PMV super heat in cooling operation

2.TC1

(Connector CN101 (2P): Black)
1) Controls PMV under cool in heating operation

3.TC2

Outline

Operation mode

(Connector CN102 (2P): Red)
1) Controls PMV super heat in cooling operation
2) [MMU-AP007YH to AP012YH only] Controls PMV under cool in heating operation

4.TCJ

Cooling operation only without heating operation
The outdoor heat exchanger (Main heat exchanger) is used as condenser.

2. Single heating

Heating operation only without cooling operation
The outdoor heat exchanger (Main heat exchanger) is used as evaporator.

4. Collective heating

Operating heating function mainly, collective operation of cooling and heating operation
The outdoor heat exchanger (Main heat exchanger) is used as evaporator.

Reversing 4-way valve, defrost the outdoor heat exchanger with single cooling cycle.

5. Defrost

3. Collective cooling

Operating cooling function mainly, collective operation of cooling and heating operation or single
cooling operation under outdoor temperature 10˚C or below
The outdoor heat exchanger (Auxiliary heat exchanger) is used as condenser.

Indoor Unit

CAUTION

 MMU-AP007YH, AP012YH type air conditioners have no TC2 sensor.

Explanation of functional parts in indoor unit

As shown in the following table, the operation modes are provided for this model.

<Operation mode>

For the refrigerating cycle flow of each operation mode, refer to “4. System refrigerant piping schematic

diagrams” and after.

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Summary of Contents for MMY-MAP0804FT7(Z)














































































































































































































































































































































Reviews:

No comments