manualshive.com logo in svg

Toshiba MMY-MAP0804FT7(Z), Service Manual, Page: 168 / 333

Share
Download
Toshiba MMY-MAP0804FT7(Z) Service Manual Download Page 168

– 168 –

*1 When the units are connected to a group, data of the header indoor unit only can be displayed.
*2 Only a part of indoor unit types is installed with the discharge temperature sensor. This temperature is not

displayed for other types.

*3 The first digit of an CODE No. indicates the outdoor unit number.
*4 The upper digit of an CODE No. -4 indicates the outdoor unit number.

1

∗

 , 5

∗

 ... U1 outdoor unit (Header unit)

2

∗

 , 6

∗

 ... U2 outdoor unit (Follower unit 1)

3

∗

 , 7

∗

 ... U3 outdoor unit (Follower unit 2)

*5 Only the CODE No. 5* of U1 outdoor unit (Header unit) is displayed.

CODE No.

Data name

Display format

Unit

Remote controller display example

00

01

02

03

04

05

06

08

F3

F9

FA

0A

0B

0C

0D

Room temperature (During control) *

1

Room temperature (Remote controller)

Indoor suction temperature (TA)

Indoor coil temperature (TCJ)

Indoor coil temperature (TC2)

Indoor coil temperature (TC1)

Indoor discharge temperature (TF) *

2

Indoor PMV opening

Filter sign time

Suction temperature of air to air heat exchanger (TSA)

 *

2

Outside air temperature (TOA) *

2

No. of connected indoor units

Total horsepower of connected indoor units

No. of connected outdoor units

Total horsepower of outdoor units

System data

Indoor unit data *

1

 ×1

×1

×1

×1

×1

×1

×1

×1/10

×1

×1

×1

×1

×10

×1

×10

˚C

˚C

˚C

˚C

˚C

˚C

˚C

pls

h

˚C

˚C

unit

HP

unit

HP

[0024] = 24˚C

[0150] = 1500pls

[2500] = 2500h

[0048] = 48 units

[0415] = 41.5HP

[0004] = 4 units

[0420] = 42HP

[0024] = 24˚C

CODE No.

Data name

Display format

Unit

Remote controller display example

U2

U3

U1

20

21

22

23

24

25

26

27

28

29

2A

2B

2C

2D

2E

2F

30

31

32

33

34

35

36

37

38

39

3A

3B

3C

3D

3E

3F

10

11

12

13

14

15

16

17

18

19

1A

1B

1C

1D

1E

1F

High-pressure sensor detention pressure (Pd)

Low-pressure sensor detention pressure (Ps)

Compressor 1 discharge temperature (Td1)

Compressor 2 discharge temperature (Td2)

Compressor 3 discharge temperature (Td3)

Suction temperature (TS1)

Outdoor coil temperature 1 (TE1)

Outdoor coil temperature 2 (TE2)

Temperature at liquid side (TL)

Outside ambient temperature (TO)

PMV1 + 2 opening

PMV4 opening

Compressor 1 current (I1)

Compressor 2 current (I2)

Compressor 3 current (I3)

Outdoor fan current (IFan)

Outdoor unit individual data 1 *

3

×100

×100

×1

×1

×1

×1

×1

×1

×1

×1

×1

×1

×10

×10

×10

×10

MPa

MPa

˚C

˚C

˚C

˚C

˚C

˚C

˚C

˚C

pls

pls

A

A

A

A

[0123]=1.23MPa

[0024]=24˚C

[0500]=500pls

[0135]=13.5A

CODE No.

Data name

Display format

Unit

Remote controller display example

U2

U3

U1

60

61

62

63

64

65

66

67

70

71

72

73

74

75

76

77

50

51

52

53

54

55

56

57

Compressor 1 revolutions

Compressor 2 revolutions

Compressor 3 revolutions

Outdoor fan mode

Compressor IPDU 1 heat sink temperature

Compressor IPDU 2 heat sink temperature

Compressor IPDU 3 heat sink temperature

Outdoor fan IPDU heat sink temperature

[0642]=64.2rps

[0058]= 58 mode

[0024]=24 ‹C

—

—

—

—

59

5A

Pressure release *

5

Discharge temperature release *

5

[0010]=Pressure release controlled

[0001]=

Discharge temperature release controlled

Outdoor unit individual data 2 *

4

×10

×10

×10

×1

×1

×1

×1

×1

rps

rps

rps

mode

˚C

˚C

˚C

˚C

6F

7F

5F

Outdoor unit horsepower

[0014]=14HP

×1

HP

—

—

58

Heating/cooling recovery controlled *

5

[0010]=Heating recovery controlled
[0001]=Cooling recovery controlled

0: Normal
1: Recovery controlled

—

—

5B

[0100]=U2 outdoor unit release controlled
[0010]=U3 outdoor unit release controlled
[0001]=U4 outdoor unit release controlled

0: Normal
1: Release controlled

Follower unit release
(U2/U2/U4 outdoor units) *

5

AMP Air Conditioning

www.ampair.co.uk | [email protected]

Summary of Contents for MMY-MAP0804FT7(Z)














































































































































































































































































































































Reviews:

No comments