Toshiba MMD-VN1002HEX1E, Installation Manual

Page: 82 / 86

– 81 –
H08 H08
01: TK1 sensor error
02: TK2 sensor error
03: TK3 sensor error
04: TK4 sensor error
05: TK5 sensor error
Oil level detection temperature sensor error I/F
H15 H15 —
Miswiring of outdoor discharge temperature sensor (TD2) I/F
H16 H16
01: TK1 oil circuit error
02: TK2 oil circuit error
03: TK3 oil circuit error
04: TK4 oil circuit error
05: TK5 oil circuit error
Oil detection circuit error I/F
H25 H25 —
Miswiring of outdoor discharge temperature sensor (TD3) I/F
L02 — —
Outdoor unit model mismatch error Indoor
L03 — —
Duplicate header indoor units Indoor
L04 L04 —
Duplicate outdoor line addresses I/F
L05 — —
Duplicate prior indoor (Displayed for prior indoor) I/F
L06 L06
Number of prior indoor
units
Duplicate prior indoor (Displayed for non-prior indoor) I/F
L07 — —
Group line in an individual indoor unit Indoor
L08 L08 —
Indoor group address not set Indoor I/F
L09 — —
Indoor capacity not set Indoor
L10 L10 —
Outdoor capacity not set I/F
L20 — —
Duplicate central control addresses Indoor
L26 L26
Number of connected
thermal units
Number of connected thermal units exceeded I/F
L27 L27
Number of connected
thermal units
Number of connected thermal units error I/F
L28 L28 — Number of connected outdoor units exceeded I/F
L29 L29 IPDU communication error I/F
L30 L30 Detect indoor addresses External interlock for indoor unit Indoor
— L31 — Expanded I/C error I/F
P03 P03 — Discharge temperature TD1 error I/F
P04 P04
01: Compressor 1
02: Compressor 2
03: Compressor 3
High-pressure SW activation IPDU
P05 P05
01: Open phase detected
02: Phase sequence error
Open phase detected, Phase sequence error I/F
Wired
remote
controller
display
Check code
Check code name
Judging
device
7 segment display on the
outdoor unit
Auxiliary code
○ : IPDU error
A3-IPDU
Fan IPDU
1 2 3
01 ○
02 ○
03 ○ ○
04 ○
05 ○ ○
06 ○ ○
07 ○ ○ ○
08 ○
09 ○ ○
0A ○ ○
0B ○ ○ ○
0C ○ ○
0D ○ ○ ○
0E ○ ○ ○
0F ○ ○ ○ ○
 Errors detected by TCC-LINK central control device
P07 P07
01: Compressor 1
02: Compressor 2
03: Compressor 3
Heat sink overheat error IPDU I/F
P09 P09
Detect thermal addresses Thermal unit water shortage error Thermal
P10 P10 Detect indoor addresses Indoor overflow error Indoor
P13 P13 — Outdoor compressor liquid compression error I/F
P15 P15
01: TS condition
02: TD condition
Gas leak detection I/F
P17 P17 —
Discharge temperature TD2 error I/F
P19 P19
Detected outdoor unit No. Four-way valve reverse error I/F
P20 P20 —
High-pressure protection activation I/F
P22 P22
0 ✽ : IGBT circuit
1
✽
: Position detection
circuit error
3
✽
: Motor lock circuit
4 ✽ : Motor current detection
C ✽ : TH sensor error
D
✽
: TH sensor error
E ✽ : Inverter DC voltage
error (Outdoor fan)
Note: 0 – F appears in “
✽ ”
above. Ignore it.
Outdoor fan IPDU error IPDU
P26 P26
01: Compressor 1
02: Compressor 2
03: Compressor 3
G-TR short circuit protection error IPDU
P29 P29
01: Compressor 1
02: Compressor 2
03: Compressor 3
Compressor position detection circuit error IPDU
P31 — — Other indoor unit error (Follower unit error) Indoor
Wired
remote
controller
display
Check code
Check code name
Judging
device
7 segment display on the
outdoor unit
Auxiliary code
C05 — — Transmission errors of the TCC-LINK central control device
TCC-LINK
line
C06 — — Reception errors of the TCC-LINK central control device
TCC-LINK
line
C12 — — Simultaneous alarms for general-purpose device control interface
General-
purpose
device I/F
P30
Depends on the error content of the
alarmed unit.
Follower unit error
TCC-LINK
line
— —
Duplicate central control addresses
Wired
remote
controller
display
Check code
Check code name
Judging
device
7 segment display on the
outdoor unit
Auxiliary code
161-EN 162-EN
+00EH99887601-2_01EN.book Page 81 Thursday, September 15, 2016 5:23 PM