background image

– 12 – 

Attached 
banding band 

Fix it with vinyl tape 

Face the incision upward. 

Local piping side 

Attached heat insulation 
pipe 

7

 Electrical 

connection

23-EN 

24-EN 

 Heat insulation process 

Apply heat insulation for the pipes separately at liquid 
side and gas side. 
•  For the heat insulation to the pipes at gas side, use 

the material with heat-resisting temperature 120 °C 
or higher. 

•  To use the attached heat insulation pipe, apply the 

heat insulation to the pipe connecting section of the 
indoor unit securely without gap. 

REQUIREMENT

•  Apply the heat insulation to the pipe connecting 

section of the indoor unit securely up to the root 
without exposure of the pipe. (The pipe exposed to 
the outside causes water leak.) 

•  Wrap heat insulator with its slits facing up (ceiling 

side). 

 

Power supply wire and communication wires speci

fi

 cations

Power supply wire and communication wires are locally procured.
For the power supply speci

fi

 cations, follow to the table below. If capacity is little, it is dangerous because overheat 

or burnout may be caused.
For speci

fi

 cations of the power capacity of the outdoor unit and the power supply wires, refer to the Installation 

Manual attached to the outdoor unit.

Indoor unit power supply

•  For the power supply of the indoor unit, prepare the exclusive power supply separated from that of the outdoor 

unit.

•  Arrange the power supply, circuit breaker, and main switch of the indoor unit connected to the same outdoor unit 

so that they are commonly used.

•  Power supply wire speci

fi

 cation: Cable 3-core 2.5 mm², 

in conformity with Design 60245 IEC 57

.

 CAUTION

•  If incorrect / incomplete wiring is carried out, it will cause an electrical 

fi

 re or smoke.

•  Use the cord clamps attached to the product.
•  Do not damage or scratch the conductive core and inner insulator of power and system interconnection wires 

when peeling them.

•  Use the power cord and system interconnection wire of speci

fi

 ed thickness, type, and protective devices required.

•  Do not connect 220-240 V power to the terminal blocks ( ,  ,  ,  ) for control wiring. (Otherwise, the system 

will fail.)

•  Perform the electric wiring so that it does not come to contact with the high-temperature part of the pipe.

The coating may melt resulting in an accident.

REQUIREMENT

•  For power supply wiring, strictly conform to the Local Regulation in each country.
•  For wiring of power supply of the outdoor units, follow the Installation Manual of each outdoor unit.
•  After connecting wires to the terminal blocks, provide a trap and 

fi

 x wires with the cord clamp.

•  Run the refrigerant piping line and control wiring line in the same line.
•  Do not turn on the power of the indoor unit until vacuuming of the refrigerant pipes completes.

Summary of Contents for MMC-AP0157HP-E (TR)



























Reviews: