Toshiba MCY-MHP0404HT Service Manual Download Page 172

Page: 172 / 184

171

4. Replacement steps

(1) Turn off the power of the outdoor control unit. (Turn off the power of the outdoor unit.)

(2) Immediately after turning off the power of the outdoor unit, the electrolytic capacitors inside the unit will still

have a high voltage, and there is a risk of electric shocks. Therefore, wait at least 5 minutes after turning off

the power before starting the replacement procedure.

(3) Disconnect all the screws

②

and connectors which are connected to the malfunctioning fan IPDU P.C. board.

(Since the connectors may be damaged if they are pulled out by grasping their lead wires, be sure to take

hold of the connectors themselves when disconnecting them.)

(4) To remove the malfunctioning fan IPDU P.C. board, remove the four card spacers

③

first.

(When removing the fan IPDU P.C. board, take care not to damage any of the four card spacers

③

. If a

card spacer

③

has been damaged, be sure to use a card spacer

③

packed with the board, and replace the

damaged card spacer by following the steps in the service guide. Failure to replace it may cause the fan

IPDU P.C. board to malfunction.)

(5) The removed screws

②

will be used again when the service P.C. board is installed so keep them in a safe

place to ensure that they will not be lost or misplaced.

(6) When replacing the board, evenly apply silicone heat sink compound to the heat-sink surfaces of the IPM

and rectifier devices on the service P.C. board. Then install the board in the outdoor control unit. Failure to

apply the silicone heat sink compound may cause the service P.C. board to malfunction.

(7) When replacing the board, use the removed screws

②

(M3x20) to connect the disconnected lead wires

following the wiring diagram display panel.

(Check that the wires have been inserted correctly and securely to prevent connection errors.)

(8) If screws

②

are not tightened sufficiently, the contact between the components (IPM, rectifier) and heat sink

will deteriorate, possibly causing malfunctioning so pay attention when tightening the screws.

However, under no circumstances must power-driven screwdrivers or air screwdrivers be used when

installing the replacement P.C. board using such a device may damage the components.

(Screw tightening

torque: 0.55 ±0.1 N•m)

(9) If any of the components on the P.C. board have been bent in the course of the replacing the board, rework

them so that they do not come into contact with the other components.

(10) Install the cover, turn on the power, and check operation.

Summary of Contents for MCY-MHP0404HT

























































































































































































Search results

Summary of Contents for MCY-MHP0404HT

Reviews:

Toshiba MCY-MHP0404HT, Service Manual, Page: 172 / 184

Search results

Summary of Contents for MCY-MHP0404HT

Reviews: