Toshiba MCY-MHP0404HT Service Manual Download Page 162

Page: 162 / 184

161

No. Component

Procedure

Remarks

⑪

Fan motor

replacement

1) Perform Step 1 of

①

, Step 1 of

②

, Step 2 of

⑤

2) Remove the flange nut fixing the fan motor and

propeller fan.
• Turn the flange nut clockwise to loosen it.

(To tighten it, turn it counterclockwise.)

3) Remove the propeller fan.
4) Remove the fan motor leads from the motor

base.

5) Hold the fan motor and remove the 4 fixing

screws so that the fan motor does not fall off.

6) Mount a new fan motor.

CAUTION

• Note that the wiring paths of the motor bases

(upper and lower) are different.

Also, make sure to arrange the lead wires

such that water cannot get inside the

mechanical compartment.

• Tighten the flange nut by 4.9 N•m

(50 kgf•cm).

• Adjust the length of the fan motor leads at

the inverter box to take up any excess slack

and ensure that the fan motor leads do not

come in contact with the propeller fan.

• Be careful so that the heat exchanger and

fan motor lead do not come into contact.

Flange nut

Turn the flange nut clockwise to loosen it.

Propeller fan

Fan motor (upper)
Hooks
(3 positions)

Fan motor (lower)
Hooks
(4 positions)

Summary of Contents for MCY-MHP0404HT

























































































































































































Search results

Summary of Contents for MCY-MHP0404HT

Reviews:

Toshiba MCY-MHP0404HT, Service Manual, Page: 162 / 184

Search results

Summary of Contents for MCY-MHP0404HT

Reviews: