Toshiba MCY-MHP0404HT Service Manual Download Page 153

Page: 153 / 184

152

No. Component

Procedure

Remarks

②

Discharge

cabinet

1. Detachment

1) Perform Step 1 of

①

2) Remove the screws of the discharge cabinet

(upper), top of the heat exchanger plate.

(M4×10, 1 )

Heat exchanger (upper)

screw (1 position)

3) Remove the screws of the discharge cabinet

(upper) and discharge cabinet (lower).

(M4×10, 2 )

4) Remove the screws of the discharge cabinet

(upper) and fin guard (upper).

(M4×10, 3 )

5) Remove the screws of the discharge cabinet

(upper) and inverter assembly.

(M4×10, 4 )
* Remove the screws of the discharge cabinet

(lower) and partition plate.

(M4×10, 3 )

6) Remove the screws of the discharge cabinet

(upper) and motor base.

(M4×10, 2 )

Motor base

screws (2 positions)

7) As in steps 2) to 6), remove the discharge

cabinets (lower).

2. Attachment

1) Mount by reversing the detachment procedure,

attaching the lower and upper discharge

cabinets in order.
• Insert the hooking tabs into the holes in the

motor base and fix each discharge cabinet in

place with screws.

Hooking tabs

Discharge

cabinet (lower)
screws (3positions)

Fin guard

screws (3positions)

Inverter assembly

screws (4 positions)

Discharge

cabinet (upper)

Discharge

cabinet (upper)

Discharge

cabinet (lower)

Summary of Contents for MCY-MHP0404HT

























































































































































































Search results

Summary of Contents for MCY-MHP0404HT

Reviews:

Toshiba MCY-MHP0404HT, Service Manual, Page: 153 / 184

Search results

Summary of Contents for MCY-MHP0404HT

Reviews: