manualshive.com logo in svg

Toshiba MCY-MHP0404HT, Service Manual, Page: 116 / 184

Share
Download
Toshiba MCY-MHP0404HT Service Manual Download Page 116

126

P22

P22

0 : IGBT circuit

1 : Position 

detection 

circuit error

3 : Motor 

lockup error

E : Inverter DC 

voltage error 

(outdoor fan)

Note:

Although 

letters 0 to 

F appear at 

locations 

indicated 

by “ ”,

please 

ignore 

them.

IPDU

Outdoor fan 

IPDU error

All stop

(Sub code: 0 )

Fan IPDU over current 

protection circuit 

Flow of current equal to or 

greater than the specified 

value is detected during 

startup of the fan.

• Check fan motor.

• Check for defect in fan 

IPDU P.C. board.

All stop

(Sub code: 1 )

Fan IPDU position detection 

circuit

Position detection is not 

going on normally.

• Check fan motor.

• Check connection of fan 

motor connector.

• Check for defect in fan 

IPDU P.C. board.

All stop

(Sub code: 3 )

Gusty wind, an obstruction, 

or another external factor

Speed estimation is not going 

on normally.

• Check fan motor.

• Check for defect in fan 

IPDU P.C. board.

All stop

(Sub code: E )

Fan IPDU DC voltage 

protection circuit 

The DC voltage higher or 

lower than the specified value 

is detected.

• Check power voltage of the 

main power supply.

• Check for defect in fan 

IPDU P.C. board.

• Check connection of fan 

IPDU P.C. board.

P26

P26

–

IPDU

IGBT (IPM) 

short-circuit 

protection error

All stop

Overcurrent is momentarily 

detected during startup of 

compressor.

• Check connector 

connection and wiring on 

A3-IPDU P.C. board.

• Check for defect in 

compressor (layer short-

circuit).

• Check for defect in outdoor 

P.C. board (A3-IPDU).

P29

P29

–

IPDU

Compressor 

position 

detection circuit 

error

All stop

Position detection is not 

going on normally.

• Check wiring and 

connector connection.

• Check for compressor 

layer short-circuit.

• Check for defect in A3-

IPDU P.C. board.

P31

–

–

Indoor 

unit

Other indoor 

error

(group follower 

unit error)

Stop of 

corresponding 

unit

There is error in other indoor 

unit in group, resulting in 

detection of E07 / L07 / L03 / 

L08.

• Check indoor P.C. board.

Location

of

detection

Description

System status

Error detection 

condition(s)

Check items (locations)

Main 

remote 

controller

Outdoor 7-segment display

Check

code

Sub-code

Check code

115

Summary of Contents for MCY-MHP0404HT

























































































































































































Reviews:

No comments