manualshive.com logo in svg

Toshiba MCY-MHP0404HT, Service Manual, Page: 111 / 184

Share
Download
Toshiba MCY-MHP0404HT Service Manual Download Page 111

122

H03

H03

–

IPDU

Current 

detection circuit 

error

All stop

Current flow of at least 

specified magnitude is 

detected despite inverter 

compressor having been shut 

turned off.

• Check current detection 

circuit wiring.

• Check defect in outdoor 

P.C. board (A3-IPDU).

H04

H04

–

I/F

Compressor 

case thermo 

operation

All stop

Compressor case thermostat 

performed protective 

operation.

• Check compressor case 

thermo circuit.

(Connector, wiring, P.C. 

board)

• Check full opening of 

service valve. 

(Gas and liquid side)

• Check outdoor PMV 

clogging.

• Check SV4 circuit leakage.

• Check miswiring / 

misinstallation of SV4.

• Check valve open status of 

indoor PMV.

• Check 4-way valve error.

• Check refrigerant amount 

shortage.

H06

H06

–

I/F

Activation of 

low-pressure 

protection

All stop

Low-pressure Ps sensor 

detects operating pressure 

lower than 0.02 MPa.

• Check service valves to 

confirm full opening

(both gas and liquid sides).

• Check outdoor PMV for

clogging.

• Check for defect in SV2 or  

SV4 circuits.

• Check for defect in low-

pressure Ps sensor.

• Check indoor filter for 

clogging.

• Check valve opening 

status of indoor PMV.

• Check refrigerant piping for 

clogging.

• Check operation of outdoor 

fan (during heating).

• Check for insufficiency in 

refrigerant quantity.

L03

–

–

Indoor 

unit

Duplicated 

indoor outdoor 

unit

Stop of 

corresponding 

unit

There is more than one 

outdoor unit in group.

• Check indoor addresses.

• Check for any change 

made to remote controller 

connection (group / 

individual) since indoor 

address setting.

L04

L04

–

I/F

Duplicated 

outdoor line 

address

All stop

There is duplication in line 

address setting for outdoor 

units belonging to different 

refrigerant piping systems.

• Check line addresses.

L05

–

–

I/F

Duplicated 

priority indoor 

unit (as 

displayed on 

priority indoor 

unit)

All stop

More than one indoor unit 

has been set up as priority 

indoor unit.

• Check display on priority 

indoor unit.

L06

L06

No. of priority 

indoor units

I/F

Duplicated 

priority indoor 

unit (as 

displayed on 

indoor unit other 

than priority 

indoor unit)

All stop

More than one indoor unit 

have been set up as priority 

indoor unit.

• Check displays on priority 

indoor unit and outdoor 

unit.

Location

of

detection

Description

System status

Error detection 

condition(s)

Check items (locations)

Main 

remote 

controller

Outdoor 7-segment display

 

Check

code

Sub-code

Check code

• Check SV5 leak.

 

110

Summary of Contents for MCY-MHP0404HT

























































































































































































Reviews:

No comments