manualshive.com logo in svg

Toshiba MCY-MHP0404HT, Service Manual, Page: 109 / 184

Share
Download
Toshiba MCY-MHP0404HT Service Manual Download Page 109

120

F01

–

–

Indoor 

unit

Indoor TCJ 

sensor error

Stop of 

corresponding 

unit

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TCJ 

sensor connector and 

wiring.

• Check resistance 

characteristics of TCJ 

sensor.

• Check for defect in indoor 

P.C. board.

F02

–

–

Indoor 

unit

Indoor TC2 

sensor error

Stop of 

corresponding 

unit

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TC2 

sensor connector and 

wiring.

• Check resistance 

characteristics of TC2 

sensor.

• Check for defect in indoor 

P.C. board.

F03

–

–

Indoor 

unit

Indoor TC1 

sensor error

Stop of 

corresponding 

unit

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TC1 

sensor connector and 

wiring.

• Check resistance 

characteristics of TC1 

sensor.

• Check for defect in indoor 

P.C. board.

F04

F04

–

I/F

TD sensor error All stop

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TD 

sensor connector.

• Check resistance 

characteristics of TD 

sensor.

• Check for defect in outdoor 

P.C. board (I/F).

F06

F06

–

I/F

TE sensor error All stop

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TE 

sensor connectors.

• Check resistance 

characteristics of TE 

sensors.

• Check for defect in outdoor 

P.C. board (I/F).

F07

F07

–

I/F

TL sensor error All stop

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TL 

sensor connector.

• Check resistance 

characteristics of TL 

sensor.

• Check for defect in outdoor 

P.C. board (I/F).

F08

F08

–

I/F

TO sensor error All stop

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TO 

sensor connector.

• Check resistance 

characteristics of TO 

sensor.

• Check for defect in outdoor 

P.C. board (I/F).

F10

–

–

Indoor 

unit

Indoor TA 

sensor error

Stop of 

corresponding 

unit

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TA 

sensor connector and 

wiring.

• Check resistance 

characteristics of TA 

sensor.

• Check for defect in indoor 

P.C. board.

F11

–

–

Indoor 

unit

Indoor TF 

sensor error

Stop of 

corresponding 

unit

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TF 

sensor connector and 

wiring.

• Check resistance 

characteristics of TF 

sensor.

• Check for defect in indoor 

P.C. board.

F12

F12

–

I/F

TS sensor error All stop

Sensor resistance is infinity 

or zero (open / short circuit). 

• Check connection of TS 

sensor connector.

• Check resistance 

characteristics of TS 

sensor.

• Check for defect in outdoor 

P.C. board (I/F).

Location

of

detection

Description

System status

Error detection 

condition(s)

Check items (locations)

Main 

remote 

controller

Outdoor 7-segment display

Check

code

Sub-code

Check code

108

Summary of Contents for MCY-MHP0404HT

























































































































































































Reviews:

No comments