manualshive.com logo in svg

Toshiba IP edge EC, Installation Manual

The Toshiba IP edge EC offers exceptional performance and advanced features to enhance your business communication system. Ensure smooth installation with the comprehensive Installation Manual available for free download at manualshive.com. Effortlessly access the detailed manual to optimize your experience and maximize the benefits of this cutting-edge product.

Share
Download
background image

EC SERVER FAN REPLACEMENT

System Fan Failure

16-10

Installation Manual    August, 2011

EC SERVER FAN 
REPLACEMENT

Two heavy duty fans provide the cooling for the EC server. One fan is 
directly over the CPU. The other fan, mounted in the front of the chassis, 
provides cooling for the rest of the components.

The chassis top cover must be properly installed, making a good seal in 
order for the cooling air to circulate properly through the chassis and cool 
the components.

System Fan Failure

Fan speed is controlled by system temperature via a BIOS setting. 
Replace any failed fan at your earliest convenience with the same type 
and model. The system can continue to run with a failed fan as long as 
the chassis temperature remains within the safe operating range.

Replacing EC System

Fans

1.

Remove the top chassis cover while the system is still running to 
determine which of the fans has failed.

2.

After determining which fan has failed.

3.

Shutdown the IP

edge

 server. Refer to 

“SHUTDOWN SYSTEM” on 

page Chapter 6 –-2

.

Remove Server Power

After the IP

edge

 server has shutdown set the power switch to OFF. Then 

unplug the power cord.

WARNING!

Remove the power cords before continuing this 
procedure.

4.

Unplug the fan cable from the server board and remove the failed fan 
from the chassis.

5.

Replace the failed fan with an identical fan available from Toshiba.

6.

Replace the top chassis cover.

7.

Plug in the power cord then set the rear panel power switch to ON.

8.

After one minute press the power button on the front panel.

EC SERVER POWER 
SUPPLY REPLACEMENT

You must shut down the system to replace a power supply module. 
Replace with the same model, which can be ordered from Toshiba.

1.

If the server is running shut down the IP

edge

 system.

2.

Set the power switch on the rear panel to off.

3.

Unplug the power cord from the power supply module.

4.

Remove the server from the rack.

5.

Remove the top cover of the server chassis.

6.

Carefully disconnect the power supply cables.

7.

Remove the failed power supply module.

8.

Install the replacement power supply and connect the cables.

9.

Replace the chassis top cover.

Summary of Contents for IP edge EC















































































































































































































Reviews:

No comments

Related manuals for IP edge EC

Samsung SRD-1670DC Properties preview
SRD-1670DC
Brand: Samsung Pages: 7
Watchguard Firebox M470 Hardware Manual preview
Firebox M470
Brand: Watchguard Pages: 32
Vxl Itona DxxS User Manual preview
Itona DxxS
Brand: Vxl Pages: 19
xFusion Digital Technologies FusionServer G5500 V6 Manual preview
FusionServer G5500 V6
Brand: xFusion Digital Technologies Pages: 100
H3C UniServer R2700 G3 User Manual preview
UniServer R2700 G3
Brand: H3C Pages: 226
EXAGATE SYSGuard 3001 Quick Installation Manual preview
SYSGuard 3001
Brand: EXAGATE Pages: 8
Cisco Linksys WPS54G User Manual preview
Linksys WPS54G
Brand: Cisco Pages: 40
Dell E74S Reference Manual preview
E74S
Brand: Dell Pages: 25
Dell EMC PowerEdge R340 Installation And Service Manual preview
EMC PowerEdge R340
Brand: Dell Pages: 92
Dell EMC PowerEdge R640 Deployment Manual preview
EMC PowerEdge R640
Brand: Dell Pages: 78
Dell E71S Reference Manual preview
E71S
Brand: Dell Pages: 25
Dell EMC PowerEdge R740 Installation And Service Manual preview
EMC PowerEdge R740
Brand: Dell Pages: 172
Dell EMC Core XC750 Installation And Service Manual preview
EMC Core XC750
Brand: Dell Pages: 186
Dell E53S001 Installation And Service Manual preview
E53S001
Brand: Dell Pages: 110
Dell E73S Installation And Service Manual preview
E73S
Brand: Dell Pages: 138
Dell EMC Connectrix EC-1700 Series Installation And Setup Manual preview
EMC Connectrix EC-1700 Series
Brand: Dell Pages: 110
Dell EMC PowerEdge T440 Installation And Service Manual preview
EMC PowerEdge T440
Brand: Dell Pages: 156
Dell EMC PowerEdge C6420 Installation And Service Manual preview
EMC PowerEdge C6420
Brand: Dell Pages: 92

Brands by name

Popular brands

Load more brands