manualshive.com logo in svg

Toshiba GX9 ASD, Quick Start Manual

Share
Download
Toshiba GX9 ASD Quick Start Manual Download Page 43

GX9 ASD Quick Start Guide

33

Monitor Mode

The 

Monitor

 mode allows the user to monitor motor performance variables, control settings, and 

configuration data during motor operation. The items are listed and described below.

Note:

The 

Monitor

 mode is a read-only mode. The settings cannot be changed from the 

Monitor

 mode. For information on how to change the values, see the section titled 

Default Setting Changes on pg. 53

.

Note:

Any two of the Underlined monitored items may be selected for display at the 

Frequency Command

 screen while running via Program 



Utilities



 

Main 

Monitor Selections

.

Note:

The 

F701

 setting will determine if the 

Current

 and 

Voltage

 values displayed 

appear as 

A

 (Amps) and 

V

 (Voltage), or if the value is shown as a

 

%

 (percentage) 

of the ASD rating.

Frequency at Trip

 

—

 

Displays the at-trip frequency.

Frequency Reference

 — Displays the 

Frequency Setpoint

.

Output Current

 — Displays the 

Output Current

 as a percentage of the rated capacity of the 

GX9 ASD.

DC Bus Voltage

 — Displays the 

Bus Voltage

 as a percentage of the rated capacity of the 

GX9 ASD.

Output Voltage

 — Displays the 

Output Voltage

 as a percentage of the rated capacity of the 

GX9 ASD.

AM Output

 

— Displays the 

AM

 output terminal value for the function assigned to the 

AM

 terminal.

FM Output 

—

 

Displays the 

FM

 output terminal value for the function assigned to the 

FM

 terminal.

Motor OL (Overload) Trip

 

—

 

Displays the 

Motor Overload

 

Trip

 value as a percentage of the 

rated capacity of the motor.

Motor Load

 

— Displays the real-time 

Motor Load

 as a percentage of the rated capacity of the 

motor.

ASD OL (Overload) Trip

 

—

 

Displays the 

ASD Overload

 

Trip

 value as a percentage of the rated 

capacity of the ASD.

ASD Load

 

— Displays the 

ASD Load

 as a percentage of the rated capacity of the GX9 ASD.

Run Time

 — Displays the 

Cumulative Run Time

 in hours.

Compensation Frequency

 — Displays the 

Output Frequency

 after the application of the slip 

compensation correction value (Post Compensation Frequency).

DBR OL (Overload) Trip

 

— Displays the 

DBR Overload

 

Trip

 value as a percentage of the 

Dynamic Braking Resistor

 capacity.

DBR Load

 

— Displays the 

DBR Load

 as a percentage of the 

Dynamic Braking Resistor

 capacity.

Feedback (Inst) 

— Provides a status of the 

Real-Time Feedback

 in Hz.

Feedback (1 Second)

 — Provides a status of the 

1-Second Averaging

 feedback in Hz.

Torque

 

—

 

Displays the 

Output Torque

 as a percentage of the rated capacity of the GX9 ASD.

Torque Reference

 

—

 

Displays the 

Torque Reference

 as a percentage of the maximum torque 

available.

onitored 

ems

Summary of Contents for GX9 ASD





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands