manualshive.com logo in svg

Toshiba GX9 ASD, Quick Start Manual

Share
Download
Toshiba GX9 ASD Quick Start Manual Download Page 14

4

GX9 ASD Quick Start Guide

Installation Precautions

Location and Ambient Requirements

•

The TIC ASD is intended for permanent installations only.

•

Installation shall conform to the 

National Electrical Code 

(NEC) 

— Article 110

 (

Requirements 

For Electrical Installations

), all regulations of the 

Occupational Safety and Health 

Administration

, and any other applicable national, regional, or industry codes and standards.

Note:

For ALL references to the National Electrical Code (NEC), see the latest release of 

the National Electrical Code.

•

Select a mounting location that is easily accessible, has adequate personnel working space, and 

adequate illumination for adjustment, inspection, and maintenance of the equipment (refer to the 

NEC Article 110-13).

•

DO NOT

 mount the ASD in a location that would produce catastrophic results if it were to become 

dislodged from its mounting location (equipment damage or injury).

•

DO NOT

 mount the ASD in a location that would allow it to be exposed to flammable chemicals or 

gases, water, solvents, explosive/corrosive mists or gases, or other fluids.

•

Avoid installation in areas where vibration, heat, humidity, dust, fibers, metal particles, or sources 

of electrical noise are present.

•

For NEMA 1 installations, the system shall not be exposed to direct sunlight.

•

Allow proper clearance spaces for installation. Do not obstruct the ventilation openings. Refer to 

the section titled 

Installation and Connections on pg. 11

 for further information on ventilation 

requirements.

•

The ambient operating temperature range of the 

GX9 ASD

 is 14° to 104° F (-10° to 40° C).

Mounting Requirements

•

Only 

Qualified Personnel

 shall install this equipment.

•

Install the unit in a secure and upright position in a well-ventilated area.

•

As a minimum, the installation of the equipment shall conform to the 

NEC — Article 110 

(NEC), 

OSHA, as well as any other applicable national, regional, or industry codes and standards.

•

Installation practices shall conform to the latest revision of NFPA 70E Electrical Safety 

Requirements for Employee Workplaces.

•

It is the responsibility of the ASD installer/maintenance personnel to ensure that the unit is installed 

into an enclosure that will protect personnel against electric shock.

Summary of Contents for GX9 ASD





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands