manualshive.com logo in svg

Toshiba EB621, Operation Manual

Share
Download
Toshiba EB621 Operation Manual Download Page 30

18

model 2000 Ethernet Module Operation Manual

Chapter 3 Setting

3

Operation Mode

• Normal: 

The EN6 module is operated in standard condition.

• Download:

Used for downloading firmware to the EN6 module program ROM 
(flash PROM).  This mode is set in upgrading the firmware version.

• Test Program: Used for operating the test program.  Never use this mode.

IP Address Type

• Class B (General):

Used for connecting an Ethernet of integrated controllers or a 
general Ethernet.

• TOSDIC-CIE 1200:

Used for connecting a TOSDIC-CIE 1200 Ethernet. (The system 
operates according to the data set in the flash PROM.)

• Setting from Tool:

Used for operating the EN6 modules with the network 
parameters set from the Engineering tool.

Figure 3-3 Locations of Switches (EN611 to EN641, EN651, EN661)

Station address (host ID) setting 
switches 

In the case of EN651, EN661.

operation mode setting switches

Summary of Contents for EB621



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands