Toshiba e-STUDIO557 Copying Manual Download Page 43

Page: 43 / 180

2.HOW TO MAKE COPIES

Bypass Copying 41

2 HOW TO MAKE COPIES

If you select a wrong paper type, this could cause a paper misfeed or significant image trouble.

When you select a paper type, you can confirm it with the icons displayed on the equipment
status indication area as shown below.

Automatic 2-sided copying can be applied to plain paper, THICK 1, THICK 2 and THICK 3.

For OHP films (TRANSPARENCY), only 1-sided copying can be performed.

For tab paper, only 1-sided copying can be performed on its front side.

After setting the paper size and type, press [OK].

The menu returns to the BASIC menu.

Select other copy modes as required, and then press the [START] button on the control
panel.

When you copy on sheets of OHP film, remove the copied OHP film one sheet at a time as they exit
onto the receiving tray. If the sheets of OHP film pile up, they may get curled and may not be
projected properly.

Paper type

Icon

Paper type

Icon

PLAIN

—

THICK 3

THICK 1

TRANSPAREN
CY

THICK 2

TAB PAPER

Summary of Contents for e-STUDIO557




















































































































































































Search results

Summary of Contents for e-STUDIO557

Reviews:

Related manuals for e-STUDIO557

Brands by name

Popular brands

Toshiba e-STUDIO557, Copying Manual

Search results

Summary of Contents for e-STUDIO557

Reviews:

Related manuals for e-STUDIO557

Brands by name

Popular brands