manualshive.com logo in svg

Toshiba e-STUDIO557, Copying Manual

Share
Download
Toshiba e-STUDIO557 Copying Manual Download Page 166

7 CONFIRMING JOB STATUS

164    Confirming Copy Job Status

„

Confirming drawers

You can confirm the size and type-setting of the paper or the amount remaining in the drawers. During printing 
you can confirm which drawer is feeding paper.

1

Press [JOB STATUS] on the touch panel.

2

Press the [SUPPLY] tab.

During printing, the button for the drawer from which the paper is fed is highlighted.
Press [CLOSE] when you finish the confirmation. The menu returns to the one shown before you 
pressed [JOB STATUS].

When the paper in the drawer has run out during printing, [JOB STATUS] on the touch panel blinks. In this 
case, press [JOB STATUS] so that the menu for displaying the printing status will appear and the button for 
the drawer whose paper has run out will blink on this menu. Printing resumes when you add paper to this 
drawer.

 

 P.11 “Placing Paper”

Summary of Contents for e-STUDIO557





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands