Toshiba e-STUDIO557 Copying Manual Download Page 128

Page: 128 / 180

4 EDITING FUNCTIONS

126 Tab Paper

BLANK TAB INSERT

Blank tab paper is inserted at the specified pages. Copying is not performed on the tab paper.

Set the tab width using [TAB EXTENSION] in advance.

Place tab paper.

P.121 “Setting tab paper”

Place the original(s).

Press [TAB PAPER] on the EDIT menu.

Press [BLANK TAB INSERT].

Set the pages to insert tab paper.

1) Key in the page number (1 to 2000) for inserting the tab paper, and then press [SET]. If more than

one sheet of tab paper is inserted, repeat this procedure.

2) After the page number has finished being keyed in, press [OK].

In [BLANK TAB INSERT], blank tab paper is inserted at the specified pages. Up to 50 sheets of tab
paper can be inserted.

Press [OK].

Summary of Contents for e-STUDIO557




















































































































































































Search results

Summary of Contents for e-STUDIO557

Reviews:

Brands by name

Popular brands

Toshiba e-STUDIO557, Copying Manual

Search results

Summary of Contents for e-STUDIO557

Reviews:

Brands by name

Popular brands