Toshiba e-Studio477s Service Manual Download Page 34

Page: 34 / 482

e-STUDIO477S/527S/477SL

SELF-DIAGNOSTIC MODE

3 - 10

3.5

Test print mode (test mode 04)

Notes:

• When an error occurs, it is indicated on the panel, but the recovery operation is not performed.

Turn OFF the power and then back ON to clear the error.

• During test printing, the [CLEAR] button is disabled when “Wait adding toner” is displayed.

The embedded test pattern can be printed out in the test print mode (04).

[0][4]

[POWER]

OFF/ON

(Exit)

(Code)

(Media selection)

[START]

[CLEAR]

Operation

Continuous

Test Printing

Summary of Contents for e-Studio477s


























































































































































































































































































































































































































































































Search results

Summary of Contents for e-Studio477s

Reviews:

Toshiba e-Studio477s, Service Manual, Page: 34 / 482

Search results

Summary of Contents for e-Studio477s

Reviews: