manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 314 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 314

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

FIRMWARE UPDATING

8 - 26

8.5

Confirmation of the updated data

After the updating is completed, check each data version in Setting Mode (08) to confirm that the data 
were overwritten properly. 

Firmware

Code

Remarks

Updating System firmware

08-9930

System firmware version

Updating PU firmware

08-9901

PU firmware version

Updating SU firmware

08-9902

SU firmware version

Updating System software

08-8952

HD data external version

08-9900

System software version

Updating Finisher firmware

08-9904

Finisher firmware version

Updating FAX firmware

08-9905

FAX firmware version

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments