manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 25 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 25

3

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

SELF-DIAGNOSTIC MODE

3 - 1

3. SELF-DIAGNOSTIC MODE

3.1

Overview

[A] Starting each mode

To enter the desired mode, turn the power ON while pressing two digital keys designated to each mode 
(e.g. [0] and [5]) simultaneously. Hold the two keys until the [PRINT DATA] lamp is lit.

On the authentication screen displayed after starting up each mode, enter the service password, and 
then press [OK]. The password is not set by default.

Refer to "11. SELF-DIAGNOSTIC MODE" for the codes in Test mode (03), Test print mode (04), 
Adjustment mode (05), and Setting mode (08).

[B] Exiting from each mode

Shut down the equipment. When the power should be turned OFF, be sure to shut down the equipment 
by pressing the [ON/OFF] button for a few seconds.

[C] List of modes

Mode

For start

Contents

For exit

Display

Control panel 

check mode

[0] + [1] + 

[POWER]

All LEDs on the control panel are lit, and all 

the LCD pixels blink.

[POWER]

OFF/ON

-

Test mode

[0] + [3] +

[POWER]

Checks the status of input/output signals.

[POWER]

OFF/ON

100% C

TEST MODE

Test print mode [0] + [4] + 

[POWER]

Outputs the test patterns.

[POWER]

OFF/ON

100% P A4 

TEST PRINT

Adjustment 

mode

[0] + [5] + 

[POWER]

Adjusts various items.

[POWER]

OFF/ON

100% A A4 

TEST MODE

Setting mode

[0] + [8] +

[POWER]

Sets various items.

[POWER]

OFF/ON

100% D 

TEST MODE

Maintenance 

mode

[6]+[8]+

[POWER]

Maintains the scanner unit (SU) and printer 

unit (PU)

[POWER] 

OFF/ON

-

Assist mode

[3]+[C]+

[POWER]

Clears error flags or SRAM, or safely deletes 

data in the HDD or SRAM to support the 

replacement of the SYS board, SRAM or 

HDD.

[POWER] 

OFF/ON

-

HDD assist 

mode

[4]+[CLEAR]+

[POWER]

Assists the ADI-HDD by checking the type of 

the mounted HDD, reverting the HDD to a 

factory default or removing keys. 

[POWER] 

OFF/ON

-

File system 

recovery mode

[5] + [C] +

[POWER]

Checks, recovers or initializes the file system 

(HDD).

[POWER]

OFF/ON

-

SRAM clear 

mode

[6]+[CLEAR]+

[POWER]

Recovers the equipment from particular 

errors such as F800 or F900. 

[POWER] 

OFF/ON

-

List print mode

[9] + [START] +

[POWER]

Prints various lists or outputs them in a CSV 

format.

[POWER]

OFF/ON

100% L A4 

LIST PRINT

Firmware 

update mode

[4] + [9] +

[POWER]

Performs firmware update with USB device.

[POWER]

OFF/ON

-

[8] + [9] +

[POWER]

Performs firmware update with download jig.

[POWER]

OFF/ON

-

Password reset 

mode

[4] + [8] + [9]

+ [POWER]

Resets the administrator password and 

service password.

[POWER]

OFF/ON

-

SRAM data 

cloning mode

[5] + [9]

+ [POWER]

Backs up the SRAM data to USB device.

[POWER]

OFF/ON

-

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments