Toshiba e-Studio477s Service Manual Download Page 23

Page: 23 / 482

e-STUDIO477S/527S/477SL

DISASSEMBLY AND REPLACEMENT

2 - 5

2.1.6

MJ-1039 (Offline stapler)

(5) Lift the equipment up and remove the spacer.

Fig. 2-12

(1) Press the [Power] button on the control panel

to shut it down.

(2) Turn the main power switch of the equipment

off.

(3) Disconnect the power cable.
(4) Take off the right side cover.



P. 6-1 "6.1.1 Right side cover"

(5) Take off the SYS board cover.



P. 6-4 "6.1.2 SYS Board cover"

(6) Disconnect the connector.

Fig. 2-13

(7) Remove 2 screws and take off the offline

stapler.

Fig. 2-14

Summary of Contents for e-Studio477s


























































































































































































































































































































































































































































































Search results

Summary of Contents for e-Studio477s

Reviews:

Toshiba e-Studio477s, Service Manual, Page: 23 / 482

Search results

Summary of Contents for e-Studio477s

Reviews: