manualshive.com logo in svg

Toshiba e-Studio477s, Service Manual, Page: 135 / 482

Share
Download
Toshiba e-Studio477s Service Manual Download Page 135

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 31

5

[EA31] Power-ON jam

[EA40] Rear cover open jam

Finisher control PC board

• Board check
• Connector check (J7,J8)
• Harness check

Parts to be replaced

Remark

Exit transport sensor
Finisher control PC board

Classification

Error content

Paper jam in finisher section

Paper was detected at either the entrance transport sensor or the 
exit transport sensor when the power was on or the finisher's rear 
cover was closed.

Check item

Measures

Transport path

If there is paper in the paper transport path, remove the paper.

Entrance transport sensor

• Sensor check (S1)
• Connector check (P7-2)
• Harness check

Exit transport sensor

• Sensor check (S2)
• Connector check (P8-1)
• Harness check

Finisher control PC board

• Board check
• Connector check (J7,J8)
• Harness check

Parts to be replaced

Remark

Entrance transport sensor
Exit transport sensor
Finisher control PC board

Classification

Error content

Paper jam in finisher section

Jam occurred because finisher's rear cover was opened while 
finisher was transporting paper.

Check item

Measures

Transport path

If there is paper in the paper transport path, remove the paper.

Rear cover

Close the cover if it is open.

Door switch

• Switch check (SW2)
• Connector check (P2-12, P2-13)
• Harness check

Finisher control PC board

• Board check
• Connector check (J2)
• Harness check

Parts to be replaced

Remark

Door switch

Check item

Measures

Summary of Contents for e-Studio477s



































































































































































































































































































































































































































































































Reviews:

No comments