manualshive.com logo in svg

Toshiba Carrier MMD-AP0246HPUL, Service Manual, Page: 86 / 98

Share
Download
Toshiba Carrier MMD-AP0246HPUL Service Manual Download Page 86

11. DETACHMENTS

  In a section, Detachments, the models are expressed as follows for convenience.

AP0

24

 : MMD

－

AP0

246

HP

UL 

to AP0

306

HP

UL 

AP036 : MMD

－

AP0366HPUL to AP0546HPUL 

No. Part name

Procedure

Remarks

①

②

1. Detachment

1) Remove the fixing screws A which fix the suction panel.

Loosen the fixing screws B.

2) Slide the suction panel to the arrow side and then

remove the panel.

2. Attachment

1) Hook the suction panel to the fixing screws B and

tighten screws.

2) Attach the removed screws A to the original positions.

AP0

24

 type 

Electric 
parts 
box cover 

1. Detachment

1) Remove the screw A of the electric parts box cover to

loosen screw B.

2) As shown in the right figure, when sliding it toward 

arrow direction and pulling to this side, the electric
parts cover opens using the hinge part as a shaft. 

3) Take off the slit of the electric parts box cover from the

projection of the side plate and then remove the cover.

2. Attachment

1) Hook the slit of the electric parts box cover to the 

projection of the side plate, close the cover, enter
screw B in the Key hole and then slide it.

2) Fix the electric parts box cover by tightening with 

screws A and B.

Suction 
panel 

Fixing screw B 

Fixing screw A 

Fixing screw B 

Fixing screw A 

Suction 
 panel 

Suction 
 panel 

 NOTE 

  WARNING 

 Be sure to stop operation of the air conditioner before 
 work and then turn off switch of the breaker. 

 CAUTION 

 Be sure to put on gloves during working time; 
 otherwise an injury will be caused by a part, etc. 

AP036 type 

Projection on the side plate

Slit

Side plate

 

Electric parts box cover

Hinge part

Screw B

Key hole

Screw-A

 

- 86 -

Summary of Contents for Carrier MMD-AP0246HPUL



































































































Reviews:

No comments