Toshiba B-EX6T Series Key Operation Specification Download Page 124

Page: 124 / 160

123

9.9.2 USB

The menu structure of USB

Menu item

<6>INTERFACE

USB

USB SERIAL ID

USB I/F STATUS

9.9.2.1 USB SERIAL ID

・

OFF

・

9.9.2.2 USB I/F STATUS

・

OFF:

No response is returned.

・

ON:

Returns a response to the host via USB.

Notes:

1. Regardless of the setting of this parameter, the status indicating the end of issue is automatically

returned.

2. Transmission of the commands related to the status is performed as follows.

1) WS, WB, or WN command

● In the case the USB and other interface cables are connected to the printer:

Whether a status is returned or not depends on the setting of this parameter.

Example) When this parameter is set to ON and a WS or WB command is sent to the printer via

LAN, the printer returns the status via both LAN and USB.

● In the case only the USB cable is connected to the printer:

A status will be returned regardless of the setting of this parameter.

2) Status-related commands other than WS, WB and WN

Whether a status is returned or not depends on the setting of this parameter.

Example 1) When a command is sent via the interface other than USB, a status will not be

returned regardless of the setting of this parameter.

Example 2) When a command is sent via USB, whether a status is returned or not depends on

the setting of this parameter.

* When this parameter is set to OFF, no status is returned via USB even if the USB cable is

connected.

9.9.3 RS-232C

The menu structure of RS-232C

Menu item

<6>INTERFACE

RS-232C

BAUD RATE

DATA LENGTH

STOP BIT

PARITY

CONTROL

Summary of Contents for B-EX6T Series

































































































































































Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands

Toshiba B-EX6T Series, Key Operation Specification

Search results

Summary of Contents for B-EX6T Series

Reviews:

Related manuals for B-EX6T Series

Brands by name

Popular brands