1
TS90 Series Sprinkler with TurfCup
™
Installation & Adjustment Guide
Performance Data - U.S.
Performance Data - Metric
Note
: Toro service tool 995-99 (or 5/8″ nut driver) is required for main nozzle exchange. For Intermediate nozzle
exchange and main nozzle trajectory adjustment, Toro service tool 995-105 (or 5/16″ nut driver) is required.
Main Nozzle Trajectory Adjustment
The main nozzle trajectory angle is factory-set at 25°, and is adjusted
between 7°—30° by turning the Trajectory Nut through the top of
the nozzle base Turret Cover (Figure 1). Typical uses of this feature
are to increase the spray radius. Decreasing trajectory decreases the
spray radius.
NOTE: Nozzle trajectory adjustment must be made prior to
installing Turf disk.
1. Locate the small, black arrow on top of the sprinkler head.
2. Install the Trajectory Nut over black arrow so that it rests flush.
3. Place the nozzle base Turret Cover over the sprinkler head. Align
into place.
4. Using a 5/16″ (995-105) nut driver, turn the Trajectory Nut
clockwise to decrease trajectory or counterclockwise to increase
trajectory. (Figure 2)
Arc Adjustment
The TS90 series sprinkler features an adjustable arc from 40° to 330°, in 5° increments, or full-circle 360° operation. All
TS90 series sprinklers are preset to half-circle (180°) arc when shipped from the factory.
The left side of the adjustable arc is fixed, and is aligned to the left watering border by turning the ratcheting riser
assembly in the sprinkler body. The right side of the arc is aligned to the right watering border by turning the nozzle
turret while compressing and holding the adjustment band in a stationary position.
NOTE: Arc adjustment must be done before sprinkler and TurfCup assembly is installed.
Specifications
• Threaded inlet: 1″ NPT or 25mm BSP
• Overall height: 14.5″ (36,8 cm)
• Retracted height: 10.75″ (27,3 cm)
• Ratcheting riser
• Spray arc: 360° and adjustable 40°–330°
• Main nozzle trajectory: adjustable 7°–30°
• Nozzle options: 4 Main, 2 Intermediate, 1 Inner
• Radius: 71′–90′ (21,64m–27,43 m) @ 25° trajectory
• Flow rate: 28.1-50.3 GPM (106–190 LPM)
• Precipitation rate: 0.56–0.60″/hr (14,2–15,2mm/hr)
• Minimum pressure: 40 psi (2,7 bar)
• Maximum pressure: 100 psi (6,9 bar)
• Recommended pressure: 50–100 psi (3,4—6,9 bar)
• Check valve elevation rating: 6′ (1,8m)
• Stator/Drive: Constant velocity
Main / Intermediate
@ 50 psi
@ 60 psi
@ 70 psi
@ 80 psi
@ 90 psi
@ 100 psi
Stator
Type
Radius (ft) GPM Radius (ft) GPM Radius (ft) GPM Radius (ft) GPM Radius (ft) GPM Radius (ft) GPM
#5 - Green Blue
#6 - Gray
Blue
#7 - Black
Orange
#8 - Red
Blue
28.1
29.8
32.2
35.7
71
72
71
74
75
76
77
78
79
79
80
82
30.7
32.6
35.3
39.2
33.2
81
35.4
83
37.5
86
39.5
35.1
80
37.7
81
40.0
83
42.1
38.1
84
40.7
85
43.1
90
45.4
42.2
85
45.1
88
47.8
90
50.3
Medium
Medium
Medium
Medium
Nozzle Set
TS90TP-02TC
Configuration
Sprinkler Model
Main / Intermediate
@ 3,4 bar
@ 4,1 bar
@ 4,8 bar
@ 5,5 bar
@ 6,2 bar
@ 6,9 bar
Stator
Type
Radius (m) LPM Radius (m) LPM Radius (m) LPM Radius (m) LPM Radius (m) LPM Radius (m) LPM
#5 - Green
Blue
#6 - Gray
Blue
#7 - Black
Orange
#8 - Red
Blue
Medium
Medium
Medium
Medium
Nozzle Set
TS90TP-52TC
21,64
106
22,86
116
24,08
126
24,69
134
25,3
142
26,21
150
21,95
113
23,16
123
24,08
133
24,38
143
24,69
151
25,3
159
21,64
122
23,47
134
24,38
144
25,60
154
25,91
163
27,43
172
22,56
135
23,77
148
24,99
160
25,91
171
26,82
181
27,43
190
Configuration
Sprinkler Model
30°
7°
30°
7°
Turret cover
Trajectory Nut
Figure 1
Figure 2
