manualshive.com logo in svg

Toro Recycler 22in 20333, Operator'S Manual

Share
Download
Toro Recycler 22in 20333 Operator'S Manual Download Page 8

Product Overview

g270774

Figure 8

1.

Handle

8.

Spark plug

2.

Blade-control bar

9.

Side-discharge deflector

3.

Adjustment for the
self-propel drive

10.

Oil fill/dipstick

4.

Ignition switch

11.

Bag-on-demand lever

5.

Fuel-tank cap

12.

Handle knob (2)

6.

Air filter

13.

Recoil-start handle

7.

Cutting-height lever (4)

14.

Control-bar lock

g009527

Figure 9

1.

Grass bag

2.

Side-discharge chute

Specifications

Model

Weight

Length

Width

Height

40 kg

150 cm

58 cm

107 cm

20333

(89 lb)

(59 inches)

(23 inches)

(42 inches)

Attachments/Accessories

A selection of Toro approved attachments and
accessories is available for use with the machine
to enhance and expand its capabilities. Contact
your Authorized Service Dealer or authorized Toro
distributor or go to www.Toro.com for a list of all
approved attachments and accessories.

To ensure optimum performance and continued safety
certification of the machine, use only genuine Toro
replacement parts and accessories. Replacement
parts and accessories made by other manufacturers
could be dangerous, and such use could void the
product warranty.

8

 

Summary of Contents for Recycler 22in 20333





























Reviews:

No comments

Brands by name

Popular brands

Load more brands