Toro Flex-Force Power System 88714 Operator'S Manual Download Page 18

Storage

Important:

Store the machine, battery pack, and

charger only in temperatures that are within the
appropriate range; refer to

Specifications (page

10)

.

Important:

If you are storing the battery pack

for the off-season, charge it until 2 or 3 LED
indicators turn green on the battery. Do not store
a fully charged or fully depleted battery. When
you are ready to use the machine again, charge
the battery pack until the left indicator light turns
green on the charger or all 4 LED indicators turn
green on the battery.

Disconnect the machine from the power supply
(i.e., remove the battery pack) and check for
damage after use.

Clean all foreign material from the machine.

Do not store the machine with the battery pack
installed.

Store the machine, battery pack, and battery
charger in a well-ventilated place that is
inaccessible to children.

Keep the machine, battery pack, and battery
charger away from corrosive agents such as
garden chemicals and de-icing salts.

To reduce the risk of serious personal injury, do
not store the battery pack outside or in vehicles.

Store the machine, battery pack, and battery
charger in an enclosed clean, dry area.

Preparing the Battery Pack
for Recycling

Important:

Upon removal, cover the terminals of

the battery pack with heavy-duty adhesive tape.
Do not attempt to destroy or disassemble the
battery pack or remove any of its components.

Lithium-ion battery packs labeled with the
Call2Recycle seal can be recycled at any
participating retailer or battery recycling
facility in the Call2Recycle program (US
and Canada only). To locate a participating
retailer or facility closest to you, please call
1-800-822-8837 or visit www.call2recycle.org.
If you cannot locate a participating retailer or
facility nearby, or if your rechargeable battery
is not labeled with the Call2Recycle seal,
please contact your local municipality for more
information on how to responsibly recycle the
battery. If you are located outside of the US
and Canada, please contact your authorized
Toro distributor.

18

 

Summary of Contents for Flex-Force Power System 88714





















Reviews: