background image

Form No. 3435-383 Rev A

48in, 52in, or 60in E-Z Vac

Blower and Drive Kit

2016 and After Grandstand

®

Mower

Model No. 78574—Serial No. 403300000 and Up

Model No. 78575—Serial No. 403300000 and Up

Model No. 78576—Serial No. 403300000 and Up

Installation Instructions

Note:

Install this kit to use with the E-Z Vac Twin Bagger; refer to the

Operator’s Manual

for the bagger

for safety, operation, and maintenance procedures.

Safety

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.

decal136-4087

136-4087

1.

Warning—read the

Operator’s Manual

.

4.

Cutting/dismemberment hazard of hand, impeller—stay away
from moving parts; keep all guards and shields in place.

2.

Warning—wear hearing protection.

5.

Cutting/dismemberment hazard of hand, impeller—disengage
the PTO, remove the key, and wait for all moving parts to stop.

3.

Thrown object hazard—do not operate the machine without
the collection system installed and latched.

6.

Warning; loss of traction hazard—do not operate with only the
counterbalance weights installed; do not operate with only the
E-Z Vac installed; only operate with both the E-Z Vac and
counterbalance weights installed.

© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3435-383* A

 

Summary of Contents for E-Z Vac 78574









Reviews: