manualshive.com logo in svg

Toro 68013, Operator'S Manual

Share
Download
Toro 68013 Operator'S Manual Download Page 45

Troubleshooting

Problem

Possible Cause

Corrective Action

1. The fuel-valve lever is in the Off

position.

1. Move the fuel-valve lever to the On

position.

2. The choke is closed

2. Open the choke when starting a hot

engine.

3. The choke is open.

3. Close the choke when starting a cold

engine.

4. The engine On/Off switch is in the Off

position.

4. Rotate the switch to the On position.

5. The engine oil level is low (engines

with the oil-level switch).

5. Fill the engine, with the recommended

oil, to the proper level.

6. The fuel tank is empty.

6. Fill the fuel tank with fresh fuel.

7. The engine contains bad/old fuel.

7. Drain the fuel tank and carburetor.

Refuel with fresh gasoline.

8. The spark plug is fouled or improperly

gapped.

8. Gap or replace the spark plug.

9. The spark plug is wet with fuel (flooded

engine).

9. Remove the spark plug, dry it, and

install the plug. Start the engine with
the throttle in the Max position.

The engine will not start.

10. The spark-plug wire is loose or

disconnected.

10. Remove the spark-plug wire, clean the

spark-plug terminal and the terminal
socket in the boot of the spark-plug
wire, and reinstall the spark-plug wire.

1. The air filter is restricted.

1. Clean or replace the air filter element(s).

2. The engine contains bad/old fuel.

2. Drain the fuel tank and carburetor.

Refuel with fresh gasoline.

3. There is water or contamination in the

fuel.

3. Drain the fuel tank and carburetor.

Refuel with fresh gasoline.

4. The fuel line is restricted.

4. Clean the fuel filter and sediment cup.

5. The choke is closed

5. Open the choke.

6. The spark plug is worn or has buildup

on the electrodes.

6. Check the electrode gap and adjust or

replace the spark plug.

The engine lacks power or runs rough.

7. There is too much oil in the engine

crankcase.

7. Drain the oil to the proper level.

1. The belt tension is insufficient.

1. Adjust the belt tension.

2. The belts are worn.

2. Replace the belts.

3. The pulley(s) are worn.

3. Contact your Authorized Service

Dealer.

The belts slip or come off the pulleys
(models 68013, 68014, 68016, 68017,
68020, and 68021).

4. The pulley(s) are misaligned.

4. Align the pulley(s).

1. The clutch lever is not adjusted

correctly.

1. Adjust the belt tension.

The paddles rotate when the clutch lever is
in the Off position (models 68013, 68014,
68016, 68017, 68020, and 68021).

2. The belt guide is not adjusted correctly.

2. Adjust the belt guide.

The paddles rotate when the clutch lever
is in the Off position (model 68024).

1. The clutch is not adjusted correctly.

1. Contact your Authorized Service

Dealer.

1. The clutch lever is not adjusted

correctly.

1. Adjust the belt tension.

The paddles do not rotate when the clutch
lever is in the On position (models 68013,
68014, 68016, 68017, 68020, and 68021).

2. The paddles are stuck in the drum

2. Clean the paddles and drum.

The paddles do not rotate when the clutch
lever is in the On position (model 68024).

1. The clutch is not adjusted correctly.

1. Contact your Authorized Service

Dealer.

45

Summary of Contents for 68013

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands