background image

Form No. 3355-422 Rev A

CCR™ 2450 GTS® Snowthrower

Model No. 38516—Serial No. 270000001 and Up

Operator's Manual

Introduction

Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a dealer,
or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. Figure 1 identifies the
location of the model and serial numbers on the product.
Write the numbers in the space provided.

Figure 1

1. Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (Figure 2),
which signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.

Figure 2

1. Safety alert symbol

This manual uses 2 other words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

Warning

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.

This spark ignition system complies with Canadian
ICES-002

The enclosed Engine Owner’s Manual is supplied
for information regarding the US Environmental
Protection Agency (EPA) and the California Emission
Control Regulation of emission systems, maintenance,
and warranty. Replacements may be ordered through
the engine manufacturer.

Safety

This snowthrower meets or exceeds the B71.3
specifications of the American National Standards
Institute in effect at the time of production.

Read and understand the contents of this manual
before the engine is ever started.

This is the safety alert symbol. It is used to alert you

to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.

Improperly using or maintaining this snowthrower
could result in injury or death. To reduce this potential,
comply with the following safety instructions.

This snow thrower is capable of amputating hands and
feet and throwing objects. Failure to observe the following
safety instructions could result in serious injury.

Training

Read, understand and follow all instructions on the
machine and in the manual(s) before operating this unit.
Be thoroughly familiar with the controls and the proper
use of the equipment. Know how to stop the unit and
disengage the controls quickly.

Never allow children to operate the equipment. Never
allow adults to operate the equipment without proper
instruction.

© 2006—The Toro® Company

8111 Lyndale Avenue South

Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

Summary of Contents for 38516













Reviews: