background image

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals

known to the State of California to cause cancer,

birth defects, or reproductive harm.

This product complies with all relevant European directives.
For details, please see the Declaration of Incorporation (DOI)
at the back of this publication.

Introduction

This rotary-blade, lawn-cutting deck to a ride-on machine
and is intended to be used by professional, hired operators in
commercial applications. It is primarily designed for cutting
grass on well-maintained lawns in parks, sports fields, and on
commercial grounds. It is not designed for cutting brush,
mowing grass and other growth alongside highways, or for
agricultural uses.

Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.

You may contact Toro directly at www.Toro.com for product
and accessory information, help finding a dealer, or to register
your product.

Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers
of your product ready. The model and serial numbers are
stamped into a plate that is mounted on the mower housing.
Write the numbers in the space provided.

Model No.

Serial No.

This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (

Figure 1

),

which signals a hazard that may cause serious injury or death
if you do not follow the recommended precautions.

Figure 1

1.

Safety alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

2

Contact us at www.Toro.com.

Printed in the USA.

All Rights Reserved

 

Summary of Contents for 30645





























Reviews: